Version 1.0
This is a template which I use to monitor a point to point Ubiquiti link with two IS‑5AC devices; that’s what I test with.
I would think it should work with other AirOS8 devices as well. Perhaps not very well suited for “normal” access points as it creates a graph for every station connected.
It discovers the remote station and greates a graph to show noise floor, signal level, RX/TX capacity and the latency.
The only trigger in there is when the connection resets; none on disconnect.
Olivier
There are no macros links in this template.
There are no template links in this template.
Name | Description | Type | Key and additional info |
---|---|---|---|
Station List | <p>-</p> | SNMP agent |
ubntStaName<p>Update: 3600</p> |
Name | Description | Type | Key and additional info |
---|---|---|---|
Station Connection Time $1 | <p>-</p> | SNMP agent |
ubntStaConnTime[{#SNMPVALUE}]<p>Update: 30</p><p>LLD</p> |
Station MAC Address $1 | <p>-</p> | SNMP agent |
ubntStaMac[{#SNMPVALUE}]<p>Update: 3600</p><p>LLD</p> |
Station Name $1 | <p>-</p> | SNMP agent |
ubntStaName[{#SNMPVALUE}]<p>Update: 3600</p><p>LLD</p> |
Station Noise Floor $1 | <p>-</p> | SNMP agent |
ubntStaNoiseFloor[{#SNMPVALUE}]<p>Update: 30</p><p>LLD</p> |
Station Rx Capacity $1 | <p>-</p> | SNMP agent |
ubntStaRxCapacity[{#SNMPVALUE}]<p>Update: 30</p><p>LLD</p> |
Station Signal Strength $1 | <p>-</p> | SNMP agent |
ubntStaSignal[{#SNMPVALUE}]<p>Update: 30</p><p>LLD</p> |
Station Tx Capacity $1 | <p>-</p> | SNMP agent |
ubntStaTxCapacity[{#SNMPVALUE}]<p>Update: 30</p><p>LLD</p> |
Station Tx Latency $1 | <p>-</p> | SNMP agent |
ubntStaTxLatency[{#SNMPVALUE}]<p>Update: 30</p><p>LLD</p> |
Name | Description | Expression | Priority |
---|---|---|---|
Connection {#SNMPVALUE} was restarted | <p>-</p> | <p>Expression: {AirOS8:ubntStaConnTime[{#SNMPVALUE}].change(0)}<0</p><p>Recovery expression: </p> | information |
Connection {#SNMPVALUE} was restarted (LLD) | <p>-</p> | <p>Expression: {AirOS8:ubntStaConnTime[{#SNMPVALUE}].change(0)}<0</p><p>Recovery expression: </p> | information |
Version 1.0
This is a template which I use to monitor a point to point Ubiquiti link with two IS‑5AC devices; that’s what I test with.
I would think it should work with other AirOS8 devices as well. Perhaps not very well suited for “normal” access points as it creates a graph for every station connected.
It discovers the remote station and greates a graph to show noise floor, signal level, RX/TX capacity and the latency.
The only trigger in there is when the connection resets; none on disconnect.
Olivier
There are no macros links in this template.
There are no template links in this template.
Name | Description | Type | Key and additional info |
---|---|---|---|
Station List | <p>-</p> | SNMP agent |
ubntStaName<p>Update: 3600</p> |
Name | Description | Type | Key and additional info |
---|---|---|---|
Station Connection Time $1 | <p>-</p> | SNMP agent |
ubntStaConnTime[{#SNMPVALUE}]<p>Update: 30</p><p>LLD</p> |
Station MAC Address $1 | <p>-</p> | SNMP agent |
ubntStaMac[{#SNMPVALUE}]<p>Update: 3600</p><p>LLD</p> |
Station Name $1 | <p>-</p> | SNMP agent |
ubntStaName[{#SNMPVALUE}]<p>Update: 3600</p><p>LLD</p> |
Station Noise Floor $1 | <p>-</p> | SNMP agent |
ubntStaNoiseFloor[{#SNMPVALUE}]<p>Update: 30</p><p>LLD</p> |
Station Rx Capacity $1 | <p>-</p> | SNMP agent |
ubntStaRxCapacity[{#SNMPVALUE}]<p>Update: 30</p><p>LLD</p> |
Station Signal Strength $1 | <p>-</p> | SNMP agent |
ubntStaSignal[{#SNMPVALUE}]<p>Update: 30</p><p>LLD</p> |
Station Tx Capacity $1 | <p>-</p> | SNMP agent |
ubntStaTxCapacity[{#SNMPVALUE}]<p>Update: 30</p><p>LLD</p> |
Station Tx Latency $1 | <p>-</p> | SNMP agent |
ubntStaTxLatency[{#SNMPVALUE}]<p>Update: 30</p><p>LLD</p> |
Name | Description | Expression | Priority |
---|---|---|---|
Connection {#SNMPVALUE} was restarted | <p>-</p> | <p>Expression: change(/AirOS8/ubntStaConnTime[{#SNMPVALUE}])<0</p><p>Recovery expression: </p> | information |
Connection {#SNMPVALUE} was restarted (LLD) | <p>-</p> | <p>Expression: change(/AirOS8/ubntStaConnTime[{#SNMPVALUE}])<0</p><p>Recovery expression: </p> | information |
Version 1.0
This is a template which I use to monitor a point to point Ubiquiti link with two IS‑5AC devices; that’s what I test with.
I would think it should work with other AirOS8 devices as well. Perhaps not very well suited for “normal” access points as it creates a graph for every station connected.
It discovers the remote station and greates a graph to show noise floor, signal level, RX/TX capacity and the latency.
The only trigger in there is when the connection resets; none on disconnect.
Olivier
There are no macros links in this template.
There are no template links in this template.
Name | Description | Type | Key and additional info |
---|---|---|---|
Station List | <p>-</p> | SNMP agent |
ubntStaName<p>Update: 3600</p> |
Name | Description | Type | Key and additional info |
---|---|---|---|
Station Connection Time $1 | <p>-</p> | SNMP agent |
ubntStaConnTime[{#SNMPVALUE}]<p>Update: 30</p><p>LLD</p> |
Station MAC Address $1 | <p>-</p> | SNMP agent |
ubntStaMac[{#SNMPVALUE}]<p>Update: 3600</p><p>LLD</p> |
Station Name $1 | <p>-</p> | SNMP agent |
ubntStaName[{#SNMPVALUE}]<p>Update: 3600</p><p>LLD</p> |
Station Noise Floor $1 | <p>-</p> | SNMP agent |
ubntStaNoiseFloor[{#SNMPVALUE}]<p>Update: 30</p><p>LLD</p> |
Station Rx Capacity $1 | <p>-</p> | SNMP agent |
ubntStaRxCapacity[{#SNMPVALUE}]<p>Update: 30</p><p>LLD</p> |
Station Signal Strength $1 | <p>-</p> | SNMP agent |
ubntStaSignal[{#SNMPVALUE}]<p>Update: 30</p><p>LLD</p> |
Station Tx Capacity $1 | <p>-</p> | SNMP agent |
ubntStaTxCapacity[{#SNMPVALUE}]<p>Update: 30</p><p>LLD</p> |
Station Tx Latency $1 | <p>-</p> | SNMP agent |
ubntStaTxLatency[{#SNMPVALUE}]<p>Update: 30</p><p>LLD</p> |
Name | Description | Expression | Priority |
---|---|---|---|
Connection {#SNMPVALUE} was restarted | <p>-</p> | <p>Expression: change(/AirOS8/ubntStaConnTime[{#SNMPVALUE}])<0</p><p>Recovery expression: </p> | information |
Connection {#SNMPVALUE} was restarted (LLD) | <p>-</p> | <p>Expression: change(/AirOS8/ubntStaConnTime[{#SNMPVALUE}])<0</p><p>Recovery expression: </p> | information |