Cisco_SG300-52-d

Description

by padamiak, 2019.05.28, zabbix v4.0, tested on sg300 and sg200

Overview

Hi,

Here is a result of my work on Cisco SG300 witch Zabbix 4.0.

based on SNMP and LLD,
it’s working with vary numbers of interfaces,
interface is discovered only if it’s operational up (less unnecessary data),
it also monitors CPU usage, status of temperature and fan’s (if any),
tested witch SG300 and SG200 switches,
in case of SG200 you may consider updating firmware of your switch as older versions doesn’t support SNMP

Have fun

Author

deb

Macros used

There are no macros links in this template.

Template links

Name
Template Module ICMP Ping

Discovery rules

Name	Description	Type	Key and additional info
Net vlan Discovery	<p>-</p>	`SNMP agent`	net.vlan.discovery<p>Update: 89m</p>
Fan Discovery	<p>-</p>	`SNMP agent`	fan.discovery<p>Update: 1d</p>
Net If Discovery	<p>-</p>	`SNMP agent`	net.if.disco<p>Update: 88m</p>

Items collected

Name	Description	Type	Key and additional info
Device name	<p>-</p>	`SNMP agent`	system.name<p>Update: 1h</p>
Device description	<p>-</p>	`SNMP agent`	system.descr<p>Update: 1h</p>
Device contact details	<p>-</p>	`SNMP agent`	system.contact<p>Update: 1h</p>
temperature status	<p>rlPhdUnitEnvParamMonitorTemperatureStatus 1.3.6.1.4.1.9.6.1.101.53.15.1.13 Display environment monitoring chassis temperature status ok(1), overTemperatureThreshold(2), overCriticalTemperatureThreshold(3)</p>	`SNMP agent`	system.temp.status<p>Update: 180</p>
Device location	<p>-</p>	`SNMP agent`	system.location<p>Update: 1h</p>
CPU utilization	<p>CPU utilization for 5 seconds 1.3.6.1.4.1.9.6.1.101.1.7.0 CPU utilization for 1 minutes 1.3.6.1.4.1.9.6.1.101.1.8.0 CPU utilization for 5 minutes 1.3.6.1.4.1.9.6.1.101.1.9.0</p>	`SNMP agent`	system.cpu.util<p>Update: 60</p>
snmp uptime	<p>-</p>	`SNMP agent`	system.uptime<p>Update: 120</p>
vlan {#IFNAME} {#IFXENTRY}: RX bps	<p>-</p>	`SNMP agent`	net.vlan[ifInBits.{#SNMPINDEX}]<p>Update: 60</p><p>LLD</p>
vlan {#IFNAME} {#IFXENTRY}: RX broadcast	<p>-</p>	`SNMP agent`	net.vlan[ifInBroadcastPkts.{#SNMPINDEX}]<p>Update: 180</p><p>LLD</p>
vlan {#IFNAME} {#IFXENTRY}: RX errors	<p>-</p>	`SNMP agent`	net.vlan[ifInErrors.{#SNMPINDEX}]<p>Update: 180</p><p>LLD</p>
vlan {#IFNAME} {#IFXENTRY}: RX multicast	<p>-</p>	`SNMP agent`	net.vlan[ifInMulticastPkts.{#SNMPINDEX}]<p>Update: 180</p><p>LLD</p>
vlan {#IFNAME} {#IFXENTRY}: RX unicast	<p>-</p>	`SNMP agent`	net.vlan[ifInUcastPkts.{#SNMPINDEX}]<p>Update: 180</p><p>LLD</p>
vlan {#IFNAME} {#IFXENTRY}: TX bps	<p>-</p>	`SNMP agent`	net.vlan[ifOutBits.{#SNMPINDEX}]<p>Update: 60</p><p>LLD</p>
vlan {#IFNAME} {#IFXENTRY}: TX broadcast	<p>-</p>	`SNMP agent`	net.vlan[ifOutBroadcastPkts.{#SNMPINDEX}]<p>Update: 180</p><p>LLD</p>
vlan {#IFNAME} {#IFXENTRY}: TX errors	<p>-</p>	`SNMP agent`	net.vlan[ifOutErrors.{#SNMPINDEX}]<p>Update: 180</p><p>LLD</p>
vlan {#IFNAME} {#IFXENTRY}: TX multicast	<p>-</p>	`SNMP agent`	net.vlan[ifOutMulticastPkts.{#SNMPINDEX}]<p>Update: 180</p><p>LLD</p>
vlan {#IFNAME} {#IFXENTRY}: TX unicast	<p>-</p>	`SNMP agent`	net.vlan[ifOutUcastPkts.{#SNMPINDEX}]<p>Update: 180</p><p>LLD</p>
vlan {#IFNAME} {#IFXENTRY}: If Type	<p>-</p>	`SNMP agent`	net.vlan[ifType.{#SNMPINDEX}]<p>Update: 86400</p><p>LLD</p>
fan status {#SNMPINDEX}	<p>normal(1), warning(2), critical(3), shutdown(4), notPresent(5), notFunctioning(6)</p>	`SNMP agent`	system.fan[status.{#SNMPINDEX}]<p>Update: 180</p><p>LLD</p>
{#IFNAME} {#IFXENTRY}: Duplex	<p>-</p>	`SNMP agent`	net.if[dot3StatsDuplexStatus.{#SNMPINDEX}]<p>Update: 1h</p><p>LLD</p>
{#IFNAME} {#IFXENTRY}: RX bps	<p>-</p>	`SNMP agent`	net.if[ifInBits.{#SNMPINDEX}]<p>Update: 60</p><p>LLD</p>
{#IFNAME} {#IFXENTRY}: RX broadcast	<p>-</p>	`SNMP agent`	net.if[ifInBroadcastPkts.{#SNMPINDEX}]<p>Update: 180</p><p>LLD</p>
{#IFNAME} {#IFXENTRY}: RX errors	<p>-</p>	`SNMP agent`	net.if[ifInErrors.{#SNMPINDEX}]<p>Update: 180</p><p>LLD</p>
{#IFNAME} {#IFXENTRY}: RX multicast	<p>-</p>	`SNMP agent`	net.if[ifInMulticastPkts.{#SNMPINDEX}]<p>Update: 180</p><p>LLD</p>
{#IFNAME} {#IFXENTRY}: RX unicast	<p>-</p>	`SNMP agent`	net.if[ifInUcastPkts.{#SNMPINDEX}]<p>Update: 180</p><p>LLD</p>
{#IFNAME} {#IFXENTRY}: TX bps	<p>-</p>	`SNMP agent`	net.if[ifOutBits.{#SNMPINDEX}]<p>Update: 60</p><p>LLD</p>
{#IFNAME} {#IFXENTRY}: TX broadcast	<p>-</p>	`SNMP agent`	net.if[ifOutBroadcastPkts.{#SNMPINDEX}]<p>Update: 180</p><p>LLD</p>
{#IFNAME} {#IFXENTRY}: TX errors	<p>-</p>	`SNMP agent`	net.if[ifOutErrors.{#SNMPINDEX}]<p>Update: 180</p><p>LLD</p>
{#IFNAME} {#IFXENTRY}: TX multicast	<p>-</p>	`SNMP agent`	net.if[ifOutMulticastPkts.{#SNMPINDEX}]<p>Update: 180</p><p>LLD</p>
{#IFNAME} {#IFXENTRY}: TX unicast	<p>-</p>	`SNMP agent`	net.if[ifOutUcastPkts.{#SNMPINDEX}]<p>Update: 180</p><p>LLD</p>
{#IFNAME} {#IFXENTRY}: speed	<p>-</p>	`SNMP agent`	net.if[ifSpeed.{#SNMPINDEX}]<p>Update: 1h</p><p>LLD</p>
{#IFNAME} {#IFXENTRY}: If Type	<p>-</p>	`SNMP agent`	net.if[ifType.{#SNMPINDEX}]<p>Update: 86400</p><p>LLD</p>

Triggers

Name	Description	Expression	Priority
fan status problem	<p>-</p>	<p>Expression: {Cisco_SG300-52-d:system.fan[status.{#SNMPINDEX}].last()}<>1</p><p>Recovery expression: </p>	warning
{#IFNAME} {#IFXENTRY}: high input utilization	<p>-</p>	<p>Expression: {Cisco_SG300-52-d:net.if[ifInBits.{#SNMPINDEX}].avg(5m)}/{Cisco_SG300-52-d:net.if[ifSpeed.{#SNMPINDEX}].last()}>0.9</p><p>Recovery expression: </p>	warning
{#IFNAME} {#IFXENTRY}: high output utilization	<p>-</p>	<p>Expression: {Cisco_SG300-52-d:net.if[ifOutBits.{#SNMPINDEX}].avg(5m)}/{Cisco_SG300-52-d:net.if[ifSpeed.{#SNMPINDEX}].last()}>0.9</p><p>Recovery expression: </p>	warning
{#IFNAME} {#IFXENTRY}: In half-duplex mode	<p>Last value: {ITEM.LASTVALUE1}. Please check autonegotiation settings and cabling</p>	<p>Expression: {Cisco_SG300-52-d:net.if[dot3StatsDuplexStatus.{#SNMPINDEX}].last()}=2</p><p>Recovery expression: </p>	information
{#IFNAME} {#IFXENTRY}: RX errors	<p>There have been input errors in the last 20 minutes.</p>	<p>Expression: {Cisco_SG300-52-d:net.if[ifInErrors.{#SNMPINDEX}].max(20m)}>0</p><p>Recovery expression: </p>	warning
{#IFNAME} {#IFXENTRY}: TX errors	<p>There have been outpup errors in the last 20 minutes.</p>	<p>Expression: {Cisco_SG300-52-d:net.if[ifOutErrors.{#SNMPINDEX}].max(20m)}>0</p><p>Recovery expression: </p>	warning
vlan {#IFNAME} {#IFXENTRY}: RX errors	<p>There have been input errors in the last 20 minutes.</p>	<p>Expression: {Cisco_SG300-52-d:net.vlan[ifInErrors.{#SNMPINDEX}].max(20m)}>0</p><p>Recovery expression: </p>	warning
vlan {#IFNAME} {#IFXENTRY}: TX errors	<p>There have been output errors in the last 20 minutes.</p>	<p>Expression: {Cisco_SG300-52-d:net.vlan[ifOutErrors.{#SNMPINDEX}].max(20m)}>0</p><p>Recovery expression: </p>	warning
vlan {#IFNAME} {#IFXENTRY}: RX errors (LLD)	<p>There have been input errors in the last 20 minutes.</p>	<p>Expression: {Cisco_SG300-52-d:net.vlan[ifInErrors.{#SNMPINDEX}].max(20m)}>0</p><p>Recovery expression: </p>	warning
vlan {#IFNAME} {#IFXENTRY}: TX errors (LLD)	<p>There have been output errors in the last 20 minutes.</p>	<p>Expression: {Cisco_SG300-52-d:net.vlan[ifOutErrors.{#SNMPINDEX}].max(20m)}>0</p><p>Recovery expression: </p>	warning
fan status problem (LLD)	<p>-</p>	<p>Expression: {Cisco_SG300-52-d:system.fan[status.{#SNMPINDEX}].last()}<>1</p><p>Recovery expression: </p>	warning
{#IFNAME} {#IFXENTRY}: high input utilization (LLD)	<p>-</p>	<p>Expression: {Cisco_SG300-52-d:net.if[ifInBits.{#SNMPINDEX}].avg(5m)}/{Cisco_SG300-52-d:net.if[ifSpeed.{#SNMPINDEX}].last()}>0.9</p><p>Recovery expression: </p>	warning
{#IFNAME} {#IFXENTRY}: high output utilization (LLD)	<p>-</p>	<p>Expression: {Cisco_SG300-52-d:net.if[ifOutBits.{#SNMPINDEX}].avg(5m)}/{Cisco_SG300-52-d:net.if[ifSpeed.{#SNMPINDEX}].last()}>0.9</p><p>Recovery expression: </p>	warning
{#IFNAME} {#IFXENTRY}: In half-duplex mode (LLD)	<p>Last value: {ITEM.LASTVALUE1}. Please check autonegotiation settings and cabling</p>	<p>Expression: {Cisco_SG300-52-d:net.if[dot3StatsDuplexStatus.{#SNMPINDEX}].last()}=2</p><p>Recovery expression: </p>	information
{#IFNAME} {#IFXENTRY}: RX errors (LLD)	<p>There have been input errors in the last 20 minutes.</p>	<p>Expression: {Cisco_SG300-52-d:net.if[ifInErrors.{#SNMPINDEX}].max(20m)}>0</p><p>Recovery expression: </p>	warning
{#IFNAME} {#IFXENTRY}: TX errors (LLD)	<p>There have been outpup errors in the last 20 minutes.</p>	<p>Expression: {Cisco_SG300-52-d:net.if[ifOutErrors.{#SNMPINDEX}].max(20m)}>0</p><p>Recovery expression: </p>	warning

Cisco_SG300-52-d

Description

by padamiak, 2019.05.28, zabbix v4.0, tested on sg300 and sg200

Overview

Hi,

Here is a result of my work on Cisco SG300 witch Zabbix 4.0.

based on SNMP and LLD,
it’s working with vary numbers of interfaces,
interface is discovered only if it’s operational up (less unnecessary data),
it also monitors CPU usage, status of temperature and fan’s (if any),
tested witch SG300 and SG200 switches,
in case of SG200 you may consider updating firmware of your switch as older versions doesn’t support SNMP

Have fun

Author

deb

Macros used

There are no macros links in this template.

Template links

Name
Template Module ICMP Ping

Discovery rules

Name	Description	Type	Key and additional info
Net vlan Discovery	<p>-</p>	`SNMP agent`	net.vlan.discovery<p>Update: 89m</p>
Fan Discovery	<p>-</p>	`SNMP agent`	fan.discovery<p>Update: 1d</p>
Net If Discovery	<p>-</p>	`SNMP agent`	net.if.disco<p>Update: 88m</p>

Items collected

Name	Description	Type	Key and additional info
snmp uptime	<p>-</p>	`SNMP agent`	system.uptime<p>Update: 120</p>
Device contact details	<p>-</p>	`SNMP agent`	system.contact<p>Update: 1h</p>
Device name	<p>-</p>	`SNMP agent`	system.name<p>Update: 1h</p>
Device description	<p>-</p>	`SNMP agent`	system.descr<p>Update: 1h</p>
temperature status	<p>rlPhdUnitEnvParamMonitorTemperatureStatus 1.3.6.1.4.1.9.6.1.101.53.15.1.13 Display environment monitoring chassis temperature status ok(1), overTemperatureThreshold(2), overCriticalTemperatureThreshold(3)</p>	`SNMP agent`	system.temp.status<p>Update: 180</p>
CPU utilization	<p>CPU utilization for 5 seconds 1.3.6.1.4.1.9.6.1.101.1.7.0 CPU utilization for 1 minutes 1.3.6.1.4.1.9.6.1.101.1.8.0 CPU utilization for 5 minutes 1.3.6.1.4.1.9.6.1.101.1.9.0</p>	`SNMP agent`	system.cpu.util<p>Update: 60</p>
Device location	<p>-</p>	`SNMP agent`	system.location<p>Update: 1h</p>
vlan {#IFNAME} {#IFXENTRY}: RX bps	<p>-</p>	`SNMP agent`	net.vlan[ifInBits.{#SNMPINDEX}]<p>Update: 60</p><p>LLD</p>
vlan {#IFNAME} {#IFXENTRY}: RX broadcast	<p>-</p>	`SNMP agent`	net.vlan[ifInBroadcastPkts.{#SNMPINDEX}]<p>Update: 180</p><p>LLD</p>
vlan {#IFNAME} {#IFXENTRY}: RX errors	<p>-</p>	`SNMP agent`	net.vlan[ifInErrors.{#SNMPINDEX}]<p>Update: 180</p><p>LLD</p>
vlan {#IFNAME} {#IFXENTRY}: RX multicast	<p>-</p>	`SNMP agent`	net.vlan[ifInMulticastPkts.{#SNMPINDEX}]<p>Update: 180</p><p>LLD</p>
vlan {#IFNAME} {#IFXENTRY}: RX unicast	<p>-</p>	`SNMP agent`	net.vlan[ifInUcastPkts.{#SNMPINDEX}]<p>Update: 180</p><p>LLD</p>
vlan {#IFNAME} {#IFXENTRY}: TX bps	<p>-</p>	`SNMP agent`	net.vlan[ifOutBits.{#SNMPINDEX}]<p>Update: 60</p><p>LLD</p>
vlan {#IFNAME} {#IFXENTRY}: TX broadcast	<p>-</p>	`SNMP agent`	net.vlan[ifOutBroadcastPkts.{#SNMPINDEX}]<p>Update: 180</p><p>LLD</p>
vlan {#IFNAME} {#IFXENTRY}: TX errors	<p>-</p>	`SNMP agent`	net.vlan[ifOutErrors.{#SNMPINDEX}]<p>Update: 180</p><p>LLD</p>
vlan {#IFNAME} {#IFXENTRY}: TX multicast	<p>-</p>	`SNMP agent`	net.vlan[ifOutMulticastPkts.{#SNMPINDEX}]<p>Update: 180</p><p>LLD</p>
vlan {#IFNAME} {#IFXENTRY}: TX unicast	<p>-</p>	`SNMP agent`	net.vlan[ifOutUcastPkts.{#SNMPINDEX}]<p>Update: 180</p><p>LLD</p>
vlan {#IFNAME} {#IFXENTRY}: If Type	<p>-</p>	`SNMP agent`	net.vlan[ifType.{#SNMPINDEX}]<p>Update: 86400</p><p>LLD</p>
fan status {#SNMPINDEX}	<p>normal(1), warning(2), critical(3), shutdown(4), notPresent(5), notFunctioning(6)</p>	`SNMP agent`	system.fan[status.{#SNMPINDEX}]<p>Update: 180</p><p>LLD</p>
{#IFNAME} {#IFXENTRY}: Duplex	<p>-</p>	`SNMP agent`	net.if[dot3StatsDuplexStatus.{#SNMPINDEX}]<p>Update: 1h</p><p>LLD</p>
{#IFNAME} {#IFXENTRY}: RX bps	<p>-</p>	`SNMP agent`	net.if[ifInBits.{#SNMPINDEX}]<p>Update: 60</p><p>LLD</p>
{#IFNAME} {#IFXENTRY}: RX broadcast	<p>-</p>	`SNMP agent`	net.if[ifInBroadcastPkts.{#SNMPINDEX}]<p>Update: 180</p><p>LLD</p>
{#IFNAME} {#IFXENTRY}: RX errors	<p>-</p>	`SNMP agent`	net.if[ifInErrors.{#SNMPINDEX}]<p>Update: 180</p><p>LLD</p>
{#IFNAME} {#IFXENTRY}: RX multicast	<p>-</p>	`SNMP agent`	net.if[ifInMulticastPkts.{#SNMPINDEX}]<p>Update: 180</p><p>LLD</p>
{#IFNAME} {#IFXENTRY}: RX unicast	<p>-</p>	`SNMP agent`	net.if[ifInUcastPkts.{#SNMPINDEX}]<p>Update: 180</p><p>LLD</p>
{#IFNAME} {#IFXENTRY}: TX bps	<p>-</p>	`SNMP agent`	net.if[ifOutBits.{#SNMPINDEX}]<p>Update: 60</p><p>LLD</p>
{#IFNAME} {#IFXENTRY}: TX broadcast	<p>-</p>	`SNMP agent`	net.if[ifOutBroadcastPkts.{#SNMPINDEX}]<p>Update: 180</p><p>LLD</p>
{#IFNAME} {#IFXENTRY}: TX errors	<p>-</p>	`SNMP agent`	net.if[ifOutErrors.{#SNMPINDEX}]<p>Update: 180</p><p>LLD</p>
{#IFNAME} {#IFXENTRY}: TX multicast	<p>-</p>	`SNMP agent`	net.if[ifOutMulticastPkts.{#SNMPINDEX}]<p>Update: 180</p><p>LLD</p>
{#IFNAME} {#IFXENTRY}: TX unicast	<p>-</p>	`SNMP agent`	net.if[ifOutUcastPkts.{#SNMPINDEX}]<p>Update: 180</p><p>LLD</p>
{#IFNAME} {#IFXENTRY}: speed	<p>-</p>	`SNMP agent`	net.if[ifSpeed.{#SNMPINDEX}]<p>Update: 1h</p><p>LLD</p>
{#IFNAME} {#IFXENTRY}: If Type	<p>-</p>	`SNMP agent`	net.if[ifType.{#SNMPINDEX}]<p>Update: 86400</p><p>LLD</p>

Triggers

Name	Description	Expression	Priority
fan status problem	<p>-</p>	<p>Expression: last(/Cisco_SG300-52-d/system.fan[status.{#SNMPINDEX}])<>1</p><p>Recovery expression: </p>	warning
{#IFNAME} {#IFXENTRY}: high input utilization	<p>-</p>	<p>Expression: avg(/Cisco_SG300-52-d/net.if[ifInBits.{#SNMPINDEX}],5m)/last(/Cisco_SG300-52-d/net.if[ifSpeed.{#SNMPINDEX}])>0.9</p><p>Recovery expression: </p>	warning
{#IFNAME} {#IFXENTRY}: high output utilization	<p>-</p>	<p>Expression: avg(/Cisco_SG300-52-d/net.if[ifOutBits.{#SNMPINDEX}],5m)/last(/Cisco_SG300-52-d/net.if[ifSpeed.{#SNMPINDEX}])>0.9</p><p>Recovery expression: </p>	warning
{#IFNAME} {#IFXENTRY}: In half-duplex mode	<p>Last value: {ITEM.LASTVALUE1}. Please check autonegotiation settings and cabling</p>	<p>Expression: last(/Cisco_SG300-52-d/net.if[dot3StatsDuplexStatus.{#SNMPINDEX}])=2</p><p>Recovery expression: </p>	information
{#IFNAME} {#IFXENTRY}: RX errors	<p>There have been input errors in the last 20 minutes.</p>	<p>Expression: max(/Cisco_SG300-52-d/net.if[ifInErrors.{#SNMPINDEX}],20m)>0</p><p>Recovery expression: </p>	warning
{#IFNAME} {#IFXENTRY}: TX errors	<p>There have been outpup errors in the last 20 minutes.</p>	<p>Expression: max(/Cisco_SG300-52-d/net.if[ifOutErrors.{#SNMPINDEX}],20m)>0</p><p>Recovery expression: </p>	warning
vlan {#IFNAME} {#IFXENTRY}: RX errors	<p>There have been input errors in the last 20 minutes.</p>	<p>Expression: max(/Cisco_SG300-52-d/net.vlan[ifInErrors.{#SNMPINDEX}],20m)>0</p><p>Recovery expression: </p>	warning
vlan {#IFNAME} {#IFXENTRY}: TX errors	<p>There have been output errors in the last 20 minutes.</p>	<p>Expression: max(/Cisco_SG300-52-d/net.vlan[ifOutErrors.{#SNMPINDEX}],20m)>0</p><p>Recovery expression: </p>	warning
vlan {#IFNAME} {#IFXENTRY}: RX errors (LLD)	<p>There have been input errors in the last 20 minutes.</p>	<p>Expression: max(/Cisco_SG300-52-d/net.vlan[ifInErrors.{#SNMPINDEX}],20m)>0</p><p>Recovery expression: </p>	warning
vlan {#IFNAME} {#IFXENTRY}: TX errors (LLD)	<p>There have been output errors in the last 20 minutes.</p>	<p>Expression: max(/Cisco_SG300-52-d/net.vlan[ifOutErrors.{#SNMPINDEX}],20m)>0</p><p>Recovery expression: </p>	warning
fan status problem (LLD)	<p>-</p>	<p>Expression: last(/Cisco_SG300-52-d/system.fan[status.{#SNMPINDEX}])<>1</p><p>Recovery expression: </p>	warning
{#IFNAME} {#IFXENTRY}: high input utilization (LLD)	<p>-</p>	<p>Expression: avg(/Cisco_SG300-52-d/net.if[ifInBits.{#SNMPINDEX}],5m)/last(/Cisco_SG300-52-d/net.if[ifSpeed.{#SNMPINDEX}])>0.9</p><p>Recovery expression: </p>	warning
{#IFNAME} {#IFXENTRY}: high output utilization (LLD)	<p>-</p>	<p>Expression: avg(/Cisco_SG300-52-d/net.if[ifOutBits.{#SNMPINDEX}],5m)/last(/Cisco_SG300-52-d/net.if[ifSpeed.{#SNMPINDEX}])>0.9</p><p>Recovery expression: </p>	warning
{#IFNAME} {#IFXENTRY}: In half-duplex mode (LLD)	<p>Last value: {ITEM.LASTVALUE1}. Please check autonegotiation settings and cabling</p>	<p>Expression: last(/Cisco_SG300-52-d/net.if[dot3StatsDuplexStatus.{#SNMPINDEX}])=2</p><p>Recovery expression: </p>	information
{#IFNAME} {#IFXENTRY}: RX errors (LLD)	<p>There have been input errors in the last 20 minutes.</p>	<p>Expression: max(/Cisco_SG300-52-d/net.if[ifInErrors.{#SNMPINDEX}],20m)>0</p><p>Recovery expression: </p>	warning
{#IFNAME} {#IFXENTRY}: TX errors (LLD)	<p>There have been outpup errors in the last 20 minutes.</p>	<p>Expression: max(/Cisco_SG300-52-d/net.if[ifOutErrors.{#SNMPINDEX}],20m)>0</p><p>Recovery expression: </p>	warning

Cisco_SG300-52-d

Description

by padamiak, 2019.05.28, zabbix v4.0, tested on sg300 and sg200

Overview

Hi,

Here is a result of my work on Cisco SG300 witch Zabbix 4.0.

based on SNMP and LLD,
it’s working with vary numbers of interfaces,
interface is discovered only if it’s operational up (less unnecessary data),
it also monitors CPU usage, status of temperature and fan’s (if any),
tested witch SG300 and SG200 switches,
in case of SG200 you may consider updating firmware of your switch as older versions doesn’t support SNMP

Have fun

Author

deb

Macros used

There are no macros links in this template.

Template links

Name
Template Module ICMP Ping

Discovery rules

Name	Description	Type	Key and additional info
Net vlan Discovery	<p>-</p>	`SNMP agent`	net.vlan.discovery<p>Update: 89m</p>
Fan Discovery	<p>-</p>	`SNMP agent`	fan.discovery<p>Update: 1d</p>
Net If Discovery	<p>-</p>	`SNMP agent`	net.if.disco<p>Update: 88m</p>

Items collected

Name	Description	Type	Key and additional info
snmp uptime	<p>-</p>	`SNMP agent`	system.uptime<p>Update: 120</p>
Device contact details	<p>-</p>	`SNMP agent`	system.contact<p>Update: 1h</p>
Device name	<p>-</p>	`SNMP agent`	system.name<p>Update: 1h</p>
Device description	<p>-</p>	`SNMP agent`	system.descr<p>Update: 1h</p>
temperature status	<p>rlPhdUnitEnvParamMonitorTemperatureStatus 1.3.6.1.4.1.9.6.1.101.53.15.1.13 Display environment monitoring chassis temperature status ok(1), overTemperatureThreshold(2), overCriticalTemperatureThreshold(3)</p>	`SNMP agent`	system.temp.status<p>Update: 180</p>
CPU utilization	<p>CPU utilization for 5 seconds 1.3.6.1.4.1.9.6.1.101.1.7.0 CPU utilization for 1 minutes 1.3.6.1.4.1.9.6.1.101.1.8.0 CPU utilization for 5 minutes 1.3.6.1.4.1.9.6.1.101.1.9.0</p>	`SNMP agent`	system.cpu.util<p>Update: 60</p>
Device location	<p>-</p>	`SNMP agent`	system.location<p>Update: 1h</p>
vlan {#IFNAME} {#IFXENTRY}: RX bps	<p>-</p>	`SNMP agent`	net.vlan[ifInBits.{#SNMPINDEX}]<p>Update: 60</p><p>LLD</p>
vlan {#IFNAME} {#IFXENTRY}: RX broadcast	<p>-</p>	`SNMP agent`	net.vlan[ifInBroadcastPkts.{#SNMPINDEX}]<p>Update: 180</p><p>LLD</p>
vlan {#IFNAME} {#IFXENTRY}: RX errors	<p>-</p>	`SNMP agent`	net.vlan[ifInErrors.{#SNMPINDEX}]<p>Update: 180</p><p>LLD</p>
vlan {#IFNAME} {#IFXENTRY}: RX multicast	<p>-</p>	`SNMP agent`	net.vlan[ifInMulticastPkts.{#SNMPINDEX}]<p>Update: 180</p><p>LLD</p>
vlan {#IFNAME} {#IFXENTRY}: RX unicast	<p>-</p>	`SNMP agent`	net.vlan[ifInUcastPkts.{#SNMPINDEX}]<p>Update: 180</p><p>LLD</p>
vlan {#IFNAME} {#IFXENTRY}: TX bps	<p>-</p>	`SNMP agent`	net.vlan[ifOutBits.{#SNMPINDEX}]<p>Update: 60</p><p>LLD</p>
vlan {#IFNAME} {#IFXENTRY}: TX broadcast	<p>-</p>	`SNMP agent`	net.vlan[ifOutBroadcastPkts.{#SNMPINDEX}]<p>Update: 180</p><p>LLD</p>
vlan {#IFNAME} {#IFXENTRY}: TX errors	<p>-</p>	`SNMP agent`	net.vlan[ifOutErrors.{#SNMPINDEX}]<p>Update: 180</p><p>LLD</p>
vlan {#IFNAME} {#IFXENTRY}: TX multicast	<p>-</p>	`SNMP agent`	net.vlan[ifOutMulticastPkts.{#SNMPINDEX}]<p>Update: 180</p><p>LLD</p>
vlan {#IFNAME} {#IFXENTRY}: TX unicast	<p>-</p>	`SNMP agent`	net.vlan[ifOutUcastPkts.{#SNMPINDEX}]<p>Update: 180</p><p>LLD</p>
vlan {#IFNAME} {#IFXENTRY}: If Type	<p>-</p>	`SNMP agent`	net.vlan[ifType.{#SNMPINDEX}]<p>Update: 86400</p><p>LLD</p>
fan status {#SNMPINDEX}	<p>normal(1), warning(2), critical(3), shutdown(4), notPresent(5), notFunctioning(6)</p>	`SNMP agent`	system.fan[status.{#SNMPINDEX}]<p>Update: 180</p><p>LLD</p>
{#IFNAME} {#IFXENTRY}: Duplex	<p>-</p>	`SNMP agent`	net.if[dot3StatsDuplexStatus.{#SNMPINDEX}]<p>Update: 1h</p><p>LLD</p>
{#IFNAME} {#IFXENTRY}: RX bps	<p>-</p>	`SNMP agent`	net.if[ifInBits.{#SNMPINDEX}]<p>Update: 60</p><p>LLD</p>
{#IFNAME} {#IFXENTRY}: RX broadcast	<p>-</p>	`SNMP agent`	net.if[ifInBroadcastPkts.{#SNMPINDEX}]<p>Update: 180</p><p>LLD</p>
{#IFNAME} {#IFXENTRY}: RX errors	<p>-</p>	`SNMP agent`	net.if[ifInErrors.{#SNMPINDEX}]<p>Update: 180</p><p>LLD</p>
{#IFNAME} {#IFXENTRY}: RX multicast	<p>-</p>	`SNMP agent`	net.if[ifInMulticastPkts.{#SNMPINDEX}]<p>Update: 180</p><p>LLD</p>
{#IFNAME} {#IFXENTRY}: RX unicast	<p>-</p>	`SNMP agent`	net.if[ifInUcastPkts.{#SNMPINDEX}]<p>Update: 180</p><p>LLD</p>
{#IFNAME} {#IFXENTRY}: TX bps	<p>-</p>	`SNMP agent`	net.if[ifOutBits.{#SNMPINDEX}]<p>Update: 60</p><p>LLD</p>
{#IFNAME} {#IFXENTRY}: TX broadcast	<p>-</p>	`SNMP agent`	net.if[ifOutBroadcastPkts.{#SNMPINDEX}]<p>Update: 180</p><p>LLD</p>
{#IFNAME} {#IFXENTRY}: TX errors	<p>-</p>	`SNMP agent`	net.if[ifOutErrors.{#SNMPINDEX}]<p>Update: 180</p><p>LLD</p>
{#IFNAME} {#IFXENTRY}: TX multicast	<p>-</p>	`SNMP agent`	net.if[ifOutMulticastPkts.{#SNMPINDEX}]<p>Update: 180</p><p>LLD</p>
{#IFNAME} {#IFXENTRY}: TX unicast	<p>-</p>	`SNMP agent`	net.if[ifOutUcastPkts.{#SNMPINDEX}]<p>Update: 180</p><p>LLD</p>
{#IFNAME} {#IFXENTRY}: speed	<p>-</p>	`SNMP agent`	net.if[ifSpeed.{#SNMPINDEX}]<p>Update: 1h</p><p>LLD</p>
{#IFNAME} {#IFXENTRY}: If Type	<p>-</p>	`SNMP agent`	net.if[ifType.{#SNMPINDEX}]<p>Update: 86400</p><p>LLD</p>

Triggers

Name	Description	Expression	Priority
fan status problem	<p>-</p>	<p>Expression: last(/Cisco_SG300-52-d/system.fan[status.{#SNMPINDEX}])<>1</p><p>Recovery expression: </p>	warning
{#IFNAME} {#IFXENTRY}: high input utilization	<p>-</p>	<p>Expression: avg(/Cisco_SG300-52-d/net.if[ifInBits.{#SNMPINDEX}],5m)/last(/Cisco_SG300-52-d/net.if[ifSpeed.{#SNMPINDEX}])>0.9</p><p>Recovery expression: </p>	warning
{#IFNAME} {#IFXENTRY}: high output utilization	<p>-</p>	<p>Expression: avg(/Cisco_SG300-52-d/net.if[ifOutBits.{#SNMPINDEX}],5m)/last(/Cisco_SG300-52-d/net.if[ifSpeed.{#SNMPINDEX}])>0.9</p><p>Recovery expression: </p>	warning
{#IFNAME} {#IFXENTRY}: In half-duplex mode	<p>Last value: {ITEM.LASTVALUE1}. Please check autonegotiation settings and cabling</p>	<p>Expression: last(/Cisco_SG300-52-d/net.if[dot3StatsDuplexStatus.{#SNMPINDEX}])=2</p><p>Recovery expression: </p>	information
{#IFNAME} {#IFXENTRY}: RX errors	<p>There have been input errors in the last 20 minutes.</p>	<p>Expression: max(/Cisco_SG300-52-d/net.if[ifInErrors.{#SNMPINDEX}],20m)>0</p><p>Recovery expression: </p>	warning
{#IFNAME} {#IFXENTRY}: TX errors	<p>There have been outpup errors in the last 20 minutes.</p>	<p>Expression: max(/Cisco_SG300-52-d/net.if[ifOutErrors.{#SNMPINDEX}],20m)>0</p><p>Recovery expression: </p>	warning
vlan {#IFNAME} {#IFXENTRY}: RX errors	<p>There have been input errors in the last 20 minutes.</p>	<p>Expression: max(/Cisco_SG300-52-d/net.vlan[ifInErrors.{#SNMPINDEX}],20m)>0</p><p>Recovery expression: </p>	warning
vlan {#IFNAME} {#IFXENTRY}: TX errors	<p>There have been output errors in the last 20 minutes.</p>	<p>Expression: max(/Cisco_SG300-52-d/net.vlan[ifOutErrors.{#SNMPINDEX}],20m)>0</p><p>Recovery expression: </p>	warning
vlan {#IFNAME} {#IFXENTRY}: RX errors (LLD)	<p>There have been input errors in the last 20 minutes.</p>	<p>Expression: max(/Cisco_SG300-52-d/net.vlan[ifInErrors.{#SNMPINDEX}],20m)>0</p><p>Recovery expression: </p>	warning
vlan {#IFNAME} {#IFXENTRY}: TX errors (LLD)	<p>There have been output errors in the last 20 minutes.</p>	<p>Expression: max(/Cisco_SG300-52-d/net.vlan[ifOutErrors.{#SNMPINDEX}],20m)>0</p><p>Recovery expression: </p>	warning
fan status problem (LLD)	<p>-</p>	<p>Expression: last(/Cisco_SG300-52-d/system.fan[status.{#SNMPINDEX}])<>1</p><p>Recovery expression: </p>	warning
{#IFNAME} {#IFXENTRY}: high input utilization (LLD)	<p>-</p>	<p>Expression: avg(/Cisco_SG300-52-d/net.if[ifInBits.{#SNMPINDEX}],5m)/last(/Cisco_SG300-52-d/net.if[ifSpeed.{#SNMPINDEX}])>0.9</p><p>Recovery expression: </p>	warning
{#IFNAME} {#IFXENTRY}: high output utilization (LLD)	<p>-</p>	<p>Expression: avg(/Cisco_SG300-52-d/net.if[ifOutBits.{#SNMPINDEX}],5m)/last(/Cisco_SG300-52-d/net.if[ifSpeed.{#SNMPINDEX}])>0.9</p><p>Recovery expression: </p>	warning
{#IFNAME} {#IFXENTRY}: In half-duplex mode (LLD)	<p>Last value: {ITEM.LASTVALUE1}. Please check autonegotiation settings and cabling</p>	<p>Expression: last(/Cisco_SG300-52-d/net.if[dot3StatsDuplexStatus.{#SNMPINDEX}])=2</p><p>Recovery expression: </p>	information
{#IFNAME} {#IFXENTRY}: RX errors (LLD)	<p>There have been input errors in the last 20 minutes.</p>	<p>Expression: max(/Cisco_SG300-52-d/net.if[ifInErrors.{#SNMPINDEX}],20m)>0</p><p>Recovery expression: </p>	warning
{#IFNAME} {#IFXENTRY}: TX errors (LLD)	<p>There have been outpup errors in the last 20 minutes.</p>	<p>Expression: max(/Cisco_SG300-52-d/net.if[ifOutErrors.{#SNMPINDEX}],20m)>0</p><p>Recovery expression: </p>	warning

Cisco_SG300-52-d

Available versions

Cisco_SG300-52-d

Description

Overview

Author

Macros used

Template links

Discovery rules

Items collected

Triggers

Cisco_SG300-52-d

Description

Overview

Author

Macros used

Template links

Discovery rules

Items collected

Triggers

Cisco_SG300-52-d

Description

Overview

Author

Macros used

Template links

Discovery rules

Items collected

Triggers