There are no macros links in this template.
There are no template links in this template.
Name | Description | Type | Key and additional info |
---|---|---|---|
OSPF Neighbors | <p>OSPF-MIB::ospfNbrIpAddr The IP address this neighbor is using in its IP source address. Note that, on addressless links, this will not be 0.0.0.0 but the address of another of the neighbor’s interfaces.</p> | SNMP agent |
ospfNbrIpAddr<p>Update: 300</p> |
BGP Peers | <p>BGP4-MIB::bgpPeerIdentifier</p> | SNMP agent |
bgpPeerIdentifier<p>Update: 300</p> |
OSPF Interfaces | <p>OSPF-MIB::ospfIfIpAddress The IP address of this OSPF interface.</p> | SNMP agent |
ospfIfIpAddress<p>Update: 300</p> |
Name | Description | Type | Key and additional info | ||
---|---|---|---|---|---|
OSPF “{#SNMPVALUE}” Neighbour State | <p>-</p> | SNMP trap |
snmptrap[“(ospfNbrStateChange).ospfNbrIpAddr[[:space:]]{#SNMPVALUE}[[:space:]].[[:space:]][a-zA-Z]+[[:space:]]$”]<p>Update: 0</p><p>LLD</p> | ||
BGP Peer “{#SNMPINDEX}” State | <p>-</p> | SNMP trap |
snmptrap[“(bgpEstablished | bgpBackwardTransition | cbgpFsmStateChange).*bgpPeerState.{#SNMPINDEX}[[:space:]][a-zA-Z]+[[:space:]]”]<p>Update: 0</p><p>LLD</p> |
BGP Peer “{#SNMPINDEX}” State | <p>-</p> | SNMP trap |
snmptrap[“(bgpBackwardTransition | cbgpFsmStateChange).*bgpPeerState.{#SNMPINDEX}[[:space:]][a-zA-Z]+[[:space:]]”]<p>Update: 0</p><p>LLD</p> | |
OSPF Interface “{SNMPVALUE}” State | <p>-</p> | SNMP trap |
snmptrap[“ospfIfStateChange.+ospfIfIpAddress[[:space:]]{#SNMPVALUE}[[:space:]].+ospfIfState[[:space:]][a-zA-Z]+”]<p>Update: 0</p><p>LLD</p> |
Name | Description | Expression | Priority | ||
---|---|---|---|---|---|
BGP Peer “{#SNMPINDEX}”->”{#SNMPVALUE}” State changed | <p>-</p> | <p>Expression: {Template Cisco General:snmptrap[“(bgpEstablished | bgpBackwardTransition | cbgpFsmStateChange).*bgpPeerState .{#SNMPINDEX}[[:space:]][a-zA-Z]+[[:space:]]”].nodata(10m)}=0</p><p>Recovery expression: </p> | average |
BGP Peer “{#SNMPINDEX}”->”{#SNMPVALUE}” State changed | <p>-</p> | <p>Expression: {Template Cisco General:snmptrap[“(bgpBackwardTransition | cbgpFsmStateChange).*bgpPeerState .{#SNMPINDEX}[[:space:]][a-zA-Z]+[[:space:]]”].nodata(10m)}=0</p><p>Recovery expression: </p> | average | |
OSPF Interface “{#SNMPVALUE}” State has been changed | <p>-</p> | <p>Expression: {Template Cisco General:snmptrap[“ospfIfStateChange.+ospfIfIpAddress[[:space:]]{#SNMPVALUE}[[:space:]].+ospfIfState[[:space:]][a-zA-Z]+”].nodata(10m)}=0</p><p>Recovery expression: </p> | average | ||
OSPF Neighbor {#SNMPVALUE} has been changed | <p>-</p> | <p>Expression: {Template Cisco General:snmptrap[“(ospfNbrStateChange).ospfNbrIpAddr[[:space:]]{#SNMPVALUE}[[:space:]].[[:space:]][a-zA-Z]+[[:space:]]$”].nodata(10m)}=0</p><p>Recovery expression: </p> | average | ||
OSPF Neighbor {#SNMPVALUE} has been changed (LLD) | <p>-</p> | <p>Expression: {Template Cisco General:snmptrap[“(ospfNbrStateChange).ospfNbrIpAddr[[:space:]]{#SNMPVALUE}[[:space:]].[[:space:]][a-zA-Z]+[[:space:]]$”].nodata(10m)}=0</p><p>Recovery expression: </p> | average | ||
BGP Peer “{#SNMPINDEX}”->”{#SNMPVALUE}” State changed (LLD) | <p>-</p> | <p>Expression: {Template Cisco General:snmptrap[“(bgpEstablished | bgpBackwardTransition | cbgpFsmStateChange).*bgpPeerState .{#SNMPINDEX}[[:space:]][a-zA-Z]+[[:space:]]”].nodata(10m)}=0</p><p>Recovery expression: </p> | average |
BGP Peer “{#SNMPINDEX}”->”{#SNMPVALUE}” State changed (LLD) | <p>-</p> | <p>Expression: {Template Cisco General:snmptrap[“(bgpBackwardTransition | cbgpFsmStateChange).*bgpPeerState .{#SNMPINDEX}[[:space:]][a-zA-Z]+[[:space:]]”].nodata(10m)}=0</p><p>Recovery expression: </p> | average | |
OSPF Interface “{#SNMPVALUE}” State has been changed (LLD) | <p>-</p> | <p>Expression: {Template Cisco General:snmptrap[“ospfIfStateChange.+ospfIfIpAddress[[:space:]]{#SNMPVALUE}[[:space:]].+ospfIfState[[:space:]][a-zA-Z]+”].nodata(10m)}=0</p><p>Recovery expression: </p> | average |
There are no macros links in this template.
Name |
---|
Template Cisco General |
Template_Cisco_Traps |
Name | Description | Type | Key and additional info |
---|---|---|---|
BGP Peers | <p>BGP4-MIB::bgpPeerIdentifier</p> | SNMP agent |
bgpPeerIdentifier<p>Update: 300</p> |
FAN | <p>CISCO-ENVMON-MIB::ciscoEnvMonFanStatusDescr Textual description of the fan being instrumented.</p> | SNMP agent |
ciscoEnvMonFanStatusDescr<p>Update: 300</p> |
Power Supplies | <p>CISCO-ENVMON-MIB::ciscoEnvMonSupplyStatusDescr Textual description of the power supply being instrumented.</p> | SNMP agent |
ciscoEnvMonSupplyStatusDescr<p>Update: 300</p> |
Temperature Sensors | <p>CISCO-ENVMON-MIB::ciscoEnvMonTemperatureStatusDescr Textual description of the testpoint being instrumented.</p> | SNMP agent |
ciscoEnvMonTemperatureStatusDescr<p>Update: 300</p> |
Memory Pool | <p>CISCO-MEMORY-POOL-MIB::ciscoMemoryPoolName A textual name assigned to the memory pool.</p> | SNMP agent |
ciscoMemoryPoolName<p>Update: 300</p> |
CPU | <p>CISCO-PROCESS-MIB::cpmCPUTotalPhysicalIndex The entPhysicalIndex of the physical entity for which the CPU statistics in this entry are maintained. The physical entity can be a CPU chip, a group of CPUs, a CPU card etc. The exact type of this entity is described by its entPhysicalVendorType value. If the CPU statistics in this entry correspond to more than one physical entity (or to no physical entity), or if the entPhysicalTable is not supported on the SNMP agent, the value of this object must be zero.</p> | SNMP agent |
cpmCPUTotalPhysicalIndex<p>Update: 300</p> |
$1 Sensors | <p>The textual name of the physical entity.</p> | SNMP agent |
entPhysicalName[Amperage]<p>Update: 300</p> |
$1 Sensors | <p>The textual name of the physical entity.</p> | SNMP agent |
entPhysicalName[“Fan Tray”]<p>Update: 300</p> |
$1 Sensors | <p>The textual name of the physical entity.</p> | SNMP agent |
entPhysicalName[Module]<p>Update: 300</p> |
$1 Sensors | <p>The textual name of the physical entity.</p> | SNMP agent |
entPhysicalName[“Power”]<p>Update: 300</p> |
$1 Sensors | <p>The textual name of the physical entity.</p> | SNMP agent |
entPhysicalName[Voltage]<p>Update: 300</p> |
OSPF Interfaces | <p>OSPF-MIB::ospfIfIpAddress The IP address of this OSPF interface.</p> | SNMP agent |
ospfIfIpAddress<p>Update: 300</p> |
OSPF Neighbors | <p>OSPF-MIB::ospfNbrIpAddr The IP address this neighbor is using in its IP source address. Note that, on addressless links, this will not be 0.0.0.0 but the address of another of the neighbor’s interfaces.</p> | SNMP agent |
ospfNbrIpAddr<p>Update: 300</p> |
Name | Description | Type | Key and additional info | |||
---|---|---|---|---|---|---|
snmptrap (OSPF Neighbor Up/Down) | <p>-</p> | SNMP trap |
snmptrap[1.3.6.1.2.1.14.16.2.2]<p>Update: 0</p> | |||
snmptrap (BGP Neighbor Up/Down) | <p>-</p> | SNMP trap |
snmptrap[1.3.6.1.2.1.15.3.1.2 | 1.3.6.1.4.1.9.9.187.1.2.5.1.3]<p>Update: 0</p> | ||
snmptrap (IF Down) | <p>-</p> | SNMP trap |
snmptrap[.1.3.6.1.6.3.1.1.5.3]<p>Update: 0</p> | |||
snmptrap (IF Up) | <p>-</p> | SNMP trap |
snmptrap[.1.3.6.1.6.3.1.1.5.4]<p>Update: 0</p> | |||
BGP Peer “{#SNMPINDEX}” State | <p>-</p> | SNMP trap |
snmptrap[“(bgpEstablished | bgpBackwardTransition | cbgpFsmStateChange).*bgpPeerState.{#SNMPINDEX}[[:space:]][a-zA-Z]+[[:space:]]”]<p>Update: 0</p><p>LLD</p> | |
BGP Peer “{#SNMPINDEX}” State | <p>-</p> | SNMP trap |
snmptrap[“(bgpBackwardTransition | cbgpFsmStateChange).*bgpPeerState.{#SNMPINDEX}[[:space:]][a-zA-Z]+[[:space:]]”]<p>Update: 0</p><p>LLD</p> | ||
Status of FAN “$1” | <p>CISCO-ENVMON-MIB::ciscoEnvMonFanState The current state of the fan being instrumented.</p> | SNMP agent |
ciscoEnvMonFanState[”{#SNMPVALUE}”]<p>Update: 60</p><p>LLD</p> | |||
Status of Power Supply “$1” | <p>CISCO-ENVMON-MIB::ciscoEnvMonSupplyState The current state of the power supply being instrumented.</p> | SNMP agent |
ciscoEnvMonSupplyState[”{#SNMPVALUE}”]<p>Update: 60</p><p>LLD</p> | |||
SNMP traps for “{#SNMPVALUE}” sensor | <p>-</p> | SNMP trap |
snmptrap[“ciscoEnvMonTemperatureState.{#SNMPINDEX}[[:space:]](warning | critical | shutdown | normal)”]<p>Update: 0</p><p>LLD</p> |
Status of Temperature Sensor “$1” | <p>CISCO-ENVMON-MIB::ciscoEnvMonTemperatureState The current state of the testpoint being instrumented.</p> | SNMP agent |
ciscoEnvMonTemperatureState[”{#SNMPVALUE}”]<p>Update: 60</p><p>LLD</p> | |||
Temperature on Sensor “$1” | <p>CISCO-ENVMON-MIB::ciscoEnvMonTemperatureStatusValue The current measurement of the testpoint being instrumented.</p> | SNMP agent |
ciscoEnvMonTemperatureStatusValue[”{#SNMPVALUE}”]<p>Update: 60</p><p>LLD</p> | |||
Threshold Temperature on Sensor “$1” | <p>CISCO-ENVMON-MIB::ciscoEnvMonTemperatureThreshold The highest value that the associated instance of the object ciscoEnvMonTemperatureStatusValue may obtain before an emergency shutdown of the managed device is initiated.</p> | SNMP agent |
ciscoEnvMonTemperatureThreshold[”{#SNMPVALUE}”]<p>Update: 1800</p><p>LLD</p> | |||
Free memory on Memory Pool “$1” | <p>CISCO-MEMORY-POOL-MIB::ciscoMemoryPoolFree Indicates the number of bytes from the memory pool that are currently unused on the managed device.</p> | SNMP agent |
ciscoMemoryPoolFree[”{#SNMPVALUE}”]<p>Update: 60</p><p>LLD</p> | |||
Name of Memory Pool “$1” | <p>CISCO-MEMORY-POOL-MIB::ciscoMemoryPoolName A textual name assigned to the memory pool.</p> | SNMP agent |
ciscoMemoryPoolName[”{#SNMPVALUE}”]<p>Update: 3600</p><p>LLD</p> | |||
Total Memory Pool “$1” | <p>-</p> | Calculated |
ciscoMemoryPoolTotal[”{#SNMPVALUE}”]<p>Update: 3600</p><p>LLD</p> | |||
Used memory on Memory Pool “$1” | <p>CISCO-MEMORY-POOL-MIB::ciscoMemoryPoolUsed Indicates the number of bytes from the memory pool that are currently in use by applications on the managed device.</p> | SNMP agent |
ciscoMemoryPoolUsed[”{#SNMPVALUE}”]<p>Update: 300</p><p>LLD</p> | |||
CPU Usage 1min Rev ({#SNMPINDEX}) | <p>CISCO-PROCESS-MIB::cpmCPUTotal1minRev The overall CPU busy percentage in the last 1 minute period. This object deprecates the object cpmCPUTotal1min and increases the value range to (0..100).</p> | SNMP agent |
cpmCPUTotal1minRev[{#SNMPINDEX}]<p>Update: 60</p><p>LLD</p> | |||
CPU Usage 5min Rev ({#SNMPINDEX}) | <p>CISCO-PROCESS-MIB::cpmCPUTotal5minRev The overall CPU busy percentage in the last 5 minute period. This object deprecates the object cpmCPUTotal5min and increases the value range to (0..100).</p> | SNMP agent |
cpmCPUTotal5minRev[{#SNMPINDEX}]<p>Update: 300</p><p>LLD</p> | |||
CPU Usage 5sec Rev ({#SNMPINDEX}) | <p>CISCO-PROCESS-MIB::cpmCPUTotal5secRev The overall CPU busy percentage in the last 5 second period. This object deprecates the object cpmCPUTotal5sec and increases the value range to (0..100). This object is deprecated by cpmCPUTotalMonIntervalValue.</p> | SNMP agent |
cpmCPUTotal5secRev[{#SNMPINDEX}]<p>Update: 30</p><p>LLD</p> | |||
$2 of Sensor “$1” | <p>CISCO-ENTITY-SENSOR-MIB::entSensorValue This variable reports the most recent measurement seen by the sensor.</p> | SNMP agent |
entSensorValue[”{#SNMPVALUE}”,Amperage]<p>Update: 60</p><p>LLD</p> | |||
Status of $2 Sensor “$1” | <p>CISCO-ENTITY-SENSOR-MIB::entSensorStatus This variable indicates the present operational status of the sensor.</p> | SNMP agent |
entSensorStatus[”{#SNMPVALUE}”,Amperage]<p>Update: 60</p><p>LLD</p> | |||
Manufacturer of $2 “$1” | <p>ENTITY-MIB::entPhysicalMfgName The name of the manufacturer of this physical component. The preferred value is the manufacturer name string actually printed on the component itself (if present).</p> | SNMP agent |
entPhysicalMfgName[”{#SNMPVALUE}”,”Fan Tray”]<p>Update: 86400</p><p>LLD</p> | |||
Model Name of $2 “$1” | <p>ENTITY-MIB::entPhysicalModelName The vendor-specific model name identifier string associated with this physical component. The preferred value is the customer-visible part number, which may be printed on the component itself.</p> | SNMP agent |
entPhysicalModelName[”{#SNMPVALUE}”,”Fan Tray”]<p>Update: 86400</p><p>LLD</p> | |||
Operational Status of $2 “$1” | <p>CISCO-ENTITY-FRU-CONTROL-MIB::cefcFanTrayOperStatus The operational state of the fan or fan tray.</p> | SNMP agent |
cefcFanTrayOperStatus[”{#SNMPVALUE}”,”Fan Tray”]<p>Update: 60</p><p>LLD</p> | |||
Serial Number of $2 “$1” | <p>ENTITY-MIB::entPhysicalSerialNum The vendor-specific serial number string for the physical entity. The preferred value is the serial number string actually printed on the component itself (if present).</p> | SNMP agent |
entPhysicalSerialNum[”{#SNMPVALUE}”,”Fan Tray”]<p>Update: 3600</p><p>LLD</p> | |||
Manufacturer of $2 “$1” | <p>ENTITY-MIB::entPhysicalMfgName The name of the manufacturer of this physical component. The preferred value is the manufacturer name string actually printed on the component itself (if present).</p> | SNMP agent |
entPhysicalMfgName[”{#SNMPVALUE}”,”Module”]<p>Update: 86400</p><p>LLD</p> | |||
Model Name of $2 “$1” | <p>ENTITY-MIB::entPhysicalModelName The vendor-specific model name identifier string associated with this physical component. The preferred value is the customer-visible part number, which may be printed on the component itself.</p> | SNMP agent |
entPhysicalModelName[”{#SNMPVALUE}”,”Module”]<p>Update: 86400</p><p>LLD</p> | |||
Operational Status of $2 “$1” | <p>ENTITY-STATE-MIB::entStateOper The operational state for this entity.</p> | SNMP agent |
entStateOper[”{#SNMPVALUE}”,”Module”]<p>Update: 60</p><p>LLD</p> | |||
Serial Number of $2 “$1” | <p>ENTITY-MIB::entPhysicalSerialNum The vendor-specific serial number string for the physical entity. The preferred value is the serial number string actually printed on the component itself (if present).</p> | SNMP agent |
entPhysicalSerialNum[”{#SNMPVALUE}”,”Module”]<p>Update: 3600</p><p>LLD</p> | |||
Status of $2 Sensor “$1” | <p>CISCO-ENTITY-SENSOR-MIB::entSensorStatus This variable indicates the present operational status of the sensor.</p> | SNMP agent |
entSensorStatus[”{#SNMPVALUE}”,Power]<p>Update: 60</p><p>LLD</p> | |||
Value of $2 Sensor “$1” | <p>CISCO-ENTITY-SENSOR-MIB::entSensorValue This variable reports the most recent measurement seen by the sensor.</p> | SNMP agent |
entSensorValue[”{#SNMPVALUE}”,Power]<p>Update: 60</p><p>LLD</p> | |||
$2 on Sensor “$1” | <p>CISCO-ENTITY-SENSOR-MIB::entSensorValue This variable reports the most recent measurement seen by the sensor.</p> | SNMP agent |
entSensorValue[”{#SNMPVALUE}”,Voltage]<p>Update: 60</p><p>LLD</p> | |||
Status of $2 Sensor “$1” | <p>CISCO-ENTITY-SENSOR-MIB::entSensorStatus This variable indicates the present operational status of the sensor.</p> | SNMP agent |
entSensorStatus[”{#SNMPVALUE}”,Voltage]<p>Update: 60</p><p>LLD</p> | |||
OSPF Interface “{SNMPVALUE}” State | <p>-</p> | SNMP trap |
snmptrap[“ospfIfStateChange.+ospfIfIpAddress[[:space:]]{#SNMPVALUE}[[:space:]].+ospfIfState[[:space:]][a-zA-Z]+”]<p>Update: 0</p><p>LLD</p> | |||
OSPF “{#SNMPVALUE}” Neighbour State | <p>-</p> | SNMP trap |
snmptrap[“(ospfNbrStateChange).ospfNbrIpAddr[[:space:]]{#SNMPVALUE}[[:space:]].[[:space:]][a-zA-Z]+[[:space:]]$”]<p>Update: 0</p><p>LLD</p> |
Name | Description | Expression | Priority | ||
---|---|---|---|---|---|
BGP Peer “{#SNMPINDEX}”->”{#SNMPVALUE}” State changed | <p>-</p> | <p>Expression: {Template_Cisco_6500:snmptrap[“(bgpEstablished | bgpBackwardTransition | cbgpFsmStateChange).*bgpPeerState .{#SNMPINDEX}[[:space:]][a-zA-Z]+[[:space:]]”].nodata(10m)}=0</p><p>Recovery expression: </p> | average |
BGP Peer “{#SNMPINDEX}”->”{#SNMPVALUE}” State changed | <p>-</p> | <p>Expression: {Template_Cisco_6500:snmptrap[“(bgpBackwardTransition | cbgpFsmStateChange).*bgpPeerState .{#SNMPINDEX}[[:space:]][a-zA-Z]+[[:space:]]”].nodata(10m)}=0</p><p>Recovery expression: </p> | average | |
OSPF Interface “{#SNMPVALUE}” State has been changed | <p>-</p> | <p>Expression: {Template_Cisco_6500:snmptrap[“ospfIfStateChange.+ospfIfIpAddress[[:space:]]{#SNMPVALUE}[[:space:]].+ospfIfState[[:space:]][a-zA-Z]+”].nodata(10m)}=0</p><p>Recovery expression: </p> | average | ||
OSPF Neighbor {#SNMPVALUE} has been changed | <p>-</p> | <p>Expression: {Template_Cisco_6500:snmptrap[“(ospfNbrStateChange).ospfNbrIpAddr[[:space:]]{#SNMPVALUE}[[:space:]].[[:space:]][a-zA-Z]+[[:space:]]$”].nodata(10m)}=0</p><p>Recovery expression: </p> | average | ||
Power Sensor “{#SNMPVALUE}” is nonoperational | <p>-</p> | <p>Expression: {Template_Cisco_6500:entSensorStatus[”{#SNMPVALUE}”,Power].last()}=3</p><p>Recovery expression: </p> | high | ||
Power Sensor “{#SNMPVALUE}” is unavailable | <p>-</p> | <p>Expression: {Template_Cisco_6500:entSensorStatus[”{#SNMPVALUE}”,Power].last()}=2</p><p>Recovery expression: </p> | average | ||
Amperage Sensor “{#SNMPVALUE}” is nonoperational | <p>-</p> | <p>Expression: {Template_Cisco_6500:entSensorStatus[”{#SNMPVALUE}”,Amperage].last()}=3</p><p>Recovery expression: </p> | high | ||
Amperage Sensor “{#SNMPVALUE}” is unavailable | <p>-</p> | <p>Expression: {Template_Cisco_6500:entSensorStatus[”{#SNMPVALUE}”,Amperage].last()}=2</p><p>Recovery expression: </p> | average | ||
Module “{#SNMPVALUE}” is inoperable | <p>-</p> | <p>Expression: {Template_Cisco_6500:entStateOper[”{#SNMPVALUE}”,”Module”].last()}=2</p><p>Recovery expression: </p> | disaster | ||
Voltage Sensor “{#SNMPVALUE}” is nonoperational | <p>-</p> | <p>Expression: {Template_Cisco_6500:entSensorStatus[”{#SNMPVALUE}”,Voltage].last()}=3</p><p>Recovery expression: </p> | high | ||
Voltage Sensor “{#SNMPVALUE}” is unavailable | <p>-</p> | <p>Expression: {Template_Cisco_6500:entSensorStatus[”{#SNMPVALUE}”,Voltage].last()}=2</p><p>Recovery expression: </p> | average | ||
Status of Fan Tray “{#SNMPVALUE}” is in partial failure | <p>-</p> | <p>Expression: {Template_Cisco_6500:cefcFanTrayOperStatus[”{#SNMPVALUE}”,”Fan Tray”].last()}=4</p><p>Recovery expression: </p> | warning | ||
Status of Fan Tray “{#SNMPVALUE}” is powered down | <p>-</p> | <p>Expression: {Template_Cisco_6500:cefcFanTrayOperStatus[”{#SNMPVALUE}”,”Fan Tray”].last()}=3</p><p>Recovery expression: </p> | high | ||
High CPU #{#SNMPINDEX} Usage | <p>-</p> | <p>Expression: {Template_Cisco_6500:cpmCPUTotal5minRev[{#SNMPINDEX}].last()}>95</p><p>Recovery expression: </p> | high | ||
Status of FAN “{#SNMPVALUE}” is critical | <p>-</p> | <p>Expression: {Template_Cisco_6500:ciscoEnvMonFanState[”{#SNMPVALUE}”].last()}=3</p><p>Recovery expression: </p> | average | ||
Status of FAN “{#SNMPVALUE}” is non-operable | <p>-</p> | <p>Expression: {Template_Cisco_6500:ciscoEnvMonFanState[”{#SNMPVALUE}”].last()}=2</p><p>Recovery expression: </p> | warning | ||
Status of FAN “{#SNMPVALUE}” is not functioning | <p>-</p> | <p>Expression: {Template_Cisco_6500:ciscoEnvMonFanState[”{#SNMPVALUE}”].last()}=6</p><p>Recovery expression: </p> | average | ||
Status of FAN “{#SNMPVALUE}” is shutdown | <p>-</p> | <p>Expression: {Template_Cisco_6500:ciscoEnvMonFanState[”{#SNMPVALUE}”].last()}=4</p><p>Recovery expression: </p> | high | ||
High utilization of Memory Pool “{#SNMPVALUE}” | <p>-</p> | <p>Expression: {Template_Cisco_6500:ciscoMemoryPoolUsed[”{#SNMPVALUE}”].last()}>{Template_Cisco_6500:ciscoMemoryPoolTotal[”{#SNMPVALUE}”].last()}*0.9</p><p>Recovery expression: </p> | average | ||
Status of Power Supply “{#SNMPVALUE}” is critical | <p>-</p> | <p>Expression: {Template_Cisco_6500:ciscoEnvMonSupplyState[”{#SNMPVALUE}”].last()}=3</p><p>Recovery expression: </p> | average | ||
Status of Power Supply “{#SNMPVALUE}” is non-operable | <p>-</p> | <p>Expression: {Template_Cisco_6500:ciscoEnvMonSupplyState[”{#SNMPVALUE}”].last()}=2</p><p>Recovery expression: </p> | warning | ||
Status of Power Supply “{#SNMPVALUE}” is not functioning | <p>-</p> | <p>Expression: {Template_Cisco_6500:ciscoEnvMonSupplyState[”{#SNMPVALUE}”].last()}=6</p><p>Recovery expression: </p> | average | ||
Status of Power Supply “{#SNMPVALUE}” is shutdown | <p>-</p> | <p>Expression: {Template_Cisco_6500:ciscoEnvMonSupplyState[”{#SNMPVALUE}”].last()}=4</p><p>Recovery expression: </p> | high | ||
Temperature Sensor “{#SNMPVALUE}” is abnormal | <p>-</p> | <p>Expression: {Template_Cisco_6500:ciscoEnvMonTemperatureState[”{#SNMPVALUE}”].last()}=2</p><p>Recovery expression: </p> | warning | ||
Temperature Sensor “{#SNMPVALUE}” is abnormal | <p>-</p> | <p>Expression: {Template_Cisco_6500:ciscoEnvMonTemperatureState[”{#SNMPVALUE}”].last()}=3</p><p>Recovery expression: </p> | high | ||
Temperature Sensor “{#SNMPVALUE}” is not functioning | <p>-</p> | <p>Expression: {Template_Cisco_6500:ciscoEnvMonTemperatureState[”{#SNMPVALUE}”].last()}=6</p><p>Recovery expression: </p> | information | ||
Temperature Sensor “{#SNMPVALUE}” is shutdown | <p>-</p> | <p>Expression: {Template_Cisco_6500:ciscoEnvMonTemperatureState[”{#SNMPVALUE}”].last()}=4</p><p>Recovery expression: </p> | disaster | ||
BGP Peer “{#SNMPINDEX}”->”{#SNMPVALUE}” State changed (LLD) | <p>-</p> | <p>Expression: {Template_Cisco_6500:snmptrap[“(bgpEstablished | bgpBackwardTransition | cbgpFsmStateChange).*bgpPeerState .{#SNMPINDEX}[[:space:]][a-zA-Z]+[[:space:]]”].nodata(10m)}=0</p><p>Recovery expression: </p> | average |
BGP Peer “{#SNMPINDEX}”->”{#SNMPVALUE}” State changed (LLD) | <p>-</p> | <p>Expression: {Template_Cisco_6500:snmptrap[“(bgpBackwardTransition | cbgpFsmStateChange).*bgpPeerState .{#SNMPINDEX}[[:space:]][a-zA-Z]+[[:space:]]”].nodata(10m)}=0</p><p>Recovery expression: </p> | average | |
Status of FAN “{#SNMPVALUE}” is critical (LLD) | <p>-</p> | <p>Expression: {Template_Cisco_6500:ciscoEnvMonFanState[”{#SNMPVALUE}”].last()}=3</p><p>Recovery expression: </p> | average | ||
Status of FAN “{#SNMPVALUE}” is non-operable (LLD) | <p>-</p> | <p>Expression: {Template_Cisco_6500:ciscoEnvMonFanState[”{#SNMPVALUE}”].last()}=2</p><p>Recovery expression: </p> | warning | ||
Status of FAN “{#SNMPVALUE}” is not functioning (LLD) | <p>-</p> | <p>Expression: {Template_Cisco_6500:ciscoEnvMonFanState[”{#SNMPVALUE}”].last()}=6</p><p>Recovery expression: </p> | average | ||
Status of FAN “{#SNMPVALUE}” is shutdown (LLD) | <p>-</p> | <p>Expression: {Template_Cisco_6500:ciscoEnvMonFanState[”{#SNMPVALUE}”].last()}=4</p><p>Recovery expression: </p> | high | ||
Status of Power Supply “{#SNMPVALUE}” is critical (LLD) | <p>-</p> | <p>Expression: {Template_Cisco_6500:ciscoEnvMonSupplyState[”{#SNMPVALUE}”].last()}=3</p><p>Recovery expression: </p> | average | ||
Status of Power Supply “{#SNMPVALUE}” is non-operable (LLD) | <p>-</p> | <p>Expression: {Template_Cisco_6500:ciscoEnvMonSupplyState[”{#SNMPVALUE}”].last()}=2</p><p>Recovery expression: </p> | warning | ||
Status of Power Supply “{#SNMPVALUE}” is not functioning (LLD) | <p>-</p> | <p>Expression: {Template_Cisco_6500:ciscoEnvMonSupplyState[”{#SNMPVALUE}”].last()}=6</p><p>Recovery expression: </p> | average | ||
Status of Power Supply “{#SNMPVALUE}” is shutdown (LLD) | <p>-</p> | <p>Expression: {Template_Cisco_6500:ciscoEnvMonSupplyState[”{#SNMPVALUE}”].last()}=4</p><p>Recovery expression: </p> | high | ||
Temperature Sensor “{#SNMPVALUE}” is abnormal (LLD) | <p>-</p> | <p>Expression: {Template_Cisco_6500:ciscoEnvMonTemperatureState[”{#SNMPVALUE}”].last()}=2</p><p>Recovery expression: </p> | warning | ||
Temperature Sensor “{#SNMPVALUE}” is abnormal (LLD) | <p>-</p> | <p>Expression: {Template_Cisco_6500:ciscoEnvMonTemperatureState[”{#SNMPVALUE}”].last()}=3</p><p>Recovery expression: </p> | high | ||
Temperature Sensor “{#SNMPVALUE}” is not functioning (LLD) | <p>-</p> | <p>Expression: {Template_Cisco_6500:ciscoEnvMonTemperatureState[”{#SNMPVALUE}”].last()}=6</p><p>Recovery expression: </p> | information | ||
Temperature Sensor “{#SNMPVALUE}” is shutdown (LLD) | <p>-</p> | <p>Expression: {Template_Cisco_6500:ciscoEnvMonTemperatureState[”{#SNMPVALUE}”].last()}=4</p><p>Recovery expression: </p> | disaster | ||
High utilization of Memory Pool “{#SNMPVALUE}” (LLD) | <p>-</p> | <p>Expression: {Template_Cisco_6500:ciscoMemoryPoolUsed[”{#SNMPVALUE}”].last()}>{Template_Cisco_6500:ciscoMemoryPoolTotal[”{#SNMPVALUE}”].last()}*0.9</p><p>Recovery expression: </p> | average | ||
High CPU #{#SNMPINDEX} Usage (LLD) | <p>-</p> | <p>Expression: {Template_Cisco_6500:cpmCPUTotal5minRev[{#SNMPINDEX}].last()}>95</p><p>Recovery expression: </p> | high | ||
Amperage Sensor “{#SNMPVALUE}” is nonoperational (LLD) | <p>-</p> | <p>Expression: {Template_Cisco_6500:entSensorStatus[”{#SNMPVALUE}”,Amperage].last()}=3</p><p>Recovery expression: </p> | high | ||
Amperage Sensor “{#SNMPVALUE}” is unavailable (LLD) | <p>-</p> | <p>Expression: {Template_Cisco_6500:entSensorStatus[”{#SNMPVALUE}”,Amperage].last()}=2</p><p>Recovery expression: </p> | average | ||
Status of Fan Tray “{#SNMPVALUE}” is in partial failure (LLD) | <p>-</p> | <p>Expression: {Template_Cisco_6500:cefcFanTrayOperStatus[”{#SNMPVALUE}”,”Fan Tray”].last()}=4</p><p>Recovery expression: </p> | warning | ||
Status of Fan Tray “{#SNMPVALUE}” is powered down (LLD) | <p>-</p> | <p>Expression: {Template_Cisco_6500:cefcFanTrayOperStatus[”{#SNMPVALUE}”,”Fan Tray”].last()}=3</p><p>Recovery expression: </p> | high | ||
Module “{#SNMPVALUE}” is inoperable (LLD) | <p>-</p> | <p>Expression: {Template_Cisco_6500:entStateOper[”{#SNMPVALUE}”,”Module”].last()}=2</p><p>Recovery expression: </p> | disaster | ||
Power Sensor “{#SNMPVALUE}” is nonoperational (LLD) | <p>-</p> | <p>Expression: {Template_Cisco_6500:entSensorStatus[”{#SNMPVALUE}”,Power].last()}=3</p><p>Recovery expression: </p> | high | ||
Power Sensor “{#SNMPVALUE}” is unavailable (LLD) | <p>-</p> | <p>Expression: {Template_Cisco_6500:entSensorStatus[”{#SNMPVALUE}”,Power].last()}=2</p><p>Recovery expression: </p> | average | ||
Voltage Sensor “{#SNMPVALUE}” is nonoperational (LLD) | <p>-</p> | <p>Expression: {Template_Cisco_6500:entSensorStatus[”{#SNMPVALUE}”,Voltage].last()}=3</p><p>Recovery expression: </p> | high | ||
Voltage Sensor “{#SNMPVALUE}” is unavailable (LLD) | <p>-</p> | <p>Expression: {Template_Cisco_6500:entSensorStatus[”{#SNMPVALUE}”,Voltage].last()}=2</p><p>Recovery expression: </p> | average | ||
OSPF Interface “{#SNMPVALUE}” State has been changed (LLD) | <p>-</p> | <p>Expression: {Template_Cisco_6500:snmptrap[“ospfIfStateChange.+ospfIfIpAddress[[:space:]]{#SNMPVALUE}[[:space:]].+ospfIfState[[:space:]][a-zA-Z]+”].nodata(10m)}=0</p><p>Recovery expression: </p> | average | ||
OSPF Neighbor {#SNMPVALUE} has been changed (LLD) | <p>-</p> | <p>Expression: {Template_Cisco_6500:snmptrap[“(ospfNbrStateChange).ospfNbrIpAddr[[:space:]]{#SNMPVALUE}[[:space:]].[[:space:]][a-zA-Z]+[[:space:]]$”].nodata(10m)}=0</p><p>Recovery expression: </p> | average |
There are no macros links in this template.
There are no template links in this template.
There are no discovery rules in this template.
Name | Description | Type | Key and additional info | |
---|---|---|---|---|
BGP Peer State | <p>BGP4-MIB::bgpPeerState CISCO-BGP4-MIB::cbgpPeer2State The BGP peer connection state.</p> | SNMP trap |
snmptrap[“bgpPeerState | cbgpPeer2State”]<p>Update: 0</p> |
LSA has been originated | <p>OSPF-TRAP-MIB::ospfOriginateLsa</p> | SNMP trap |
snmptrap[“ospfOriginateLsa”]<p>Update: 0</p> | |
Source of Command | <p>-</p> | SNMP trap |
snmptrap[“ccmHistoryEventCommandSource”]<p>Update: 0</p> | |
OSPF Interface State | <p>OSPF-MIB::ospfIfState The OSPF Interface State.</p> | SNMP trap |
snmptrap[“ospfIfState”]<p>Update: 0</p> | |
OSPF neighbour state | <p>1 : down 2 : attempt 3 : init 4 : twoWay 5 : exchangeStart 6 : exchange 7 : loading 8 : full</p> | SNMP trap |
snmptrap[“ospfNbrStateChange.*ospfNbrState[[:space:]]”]<p>Update: 0</p> | |
SSH Sessions | <p>CISCO-SECURE-SHELL-MIB::cssSessionHostAddr</p> | SNMP trap |
snmptrap[“cssSessionHostAddr”]<p>Update: 0</p> | |
Type of remote session | <p>-</p> | SNMP trap |
snmptrap[“tslineSesType”]<p>Update: 0</p> | |
LSA aged to MaxAge | <p>-</p> | SNMP trap |
snmptrap[“ospfMaxAgeLsa”]<p>Update: 0</p> | |
Status of Attack Filter | <p>-</p> | SNMP trap |
snmptrap[“cscaFilterStatus”]<p>Update: 0</p> | |
BFD Sessions | <p>CISCO-IETF-BFD-MIB::ciscoBfdSessDown and ciscoBfdSessUp</p> | SNMP trap |
snmptrap[“ciscoBfdSess(Up | Down)”]<p>Update: 0</p> |
MPLS L3 State | <p>MPLS-L3VPN-STD-MIB::mplsL3VpnVrfUp MPLS-L3VPN-STD-MIB::mplsL3VpnVrfDown</p> | SNMP trap |
snmptrap[“mplsL3VpnVrf[Up | Down]”]<p>Update: 0</p> |
Attack Filter changes | <p>The system generates this notification to indicate that the cscaFilterStatus of the attack filter for cscaType has changed due to the reason determined by cscaDescription. The system limits the generation of this notifications for the same cscaType to a five-second interval.</p> | SNMP trap |
snmptrap[“cscaFilterChange”]<p>Update: 0</p> | |
OSP TX Retransmits | <p>-</p> | SNMP trap |
snmptrap[“ospfTxRetransmit”]<p>Update: 0</p> |
There are no triggers in this template.
There are no macros links in this template.
There are no template links in this template.
Name | Description | Type | Key and additional info |
---|---|---|---|
BGP Peers | <p>BGP4-MIB::bgpPeerIdentifier</p> | SNMP agent |
bgpPeerIdentifier<p>Update: 300</p> |
OSPF Neighbors | <p>OSPF-MIB::ospfNbrIpAddr The IP address this neighbor is using in its IP source address. Note that, on addressless links, this will not be 0.0.0.0 but the address of another of the neighbor’s interfaces.</p> | SNMP agent |
ospfNbrIpAddr<p>Update: 300</p> |
OSPF Interfaces | <p>OSPF-MIB::ospfIfIpAddress The IP address of this OSPF interface.</p> | SNMP agent |
ospfIfIpAddress<p>Update: 300</p> |
Name | Description | Type | Key and additional info | ||
---|---|---|---|---|---|
BGP Peer “{#SNMPINDEX}” State | <p>-</p> | SNMP trap |
snmptrap[“(bgpEstablished | bgpBackwardTransition | cbgpFsmStateChange).*bgpPeerState.{#SNMPINDEX}[[:space:]][a-zA-Z]+[[:space:]]”]<p>Update: 0</p><p>LLD</p> |
BGP Peer “{#SNMPINDEX}” State | <p>-</p> | SNMP trap |
snmptrap[“(bgpBackwardTransition | cbgpFsmStateChange).*bgpPeerState.{#SNMPINDEX}[[:space:]][a-zA-Z]+[[:space:]]”]<p>Update: 0</p><p>LLD</p> | |
OSPF “{#SNMPVALUE}” Neighbour State | <p>-</p> | SNMP trap |
snmptrap[“(ospfNbrStateChange).ospfNbrIpAddr[[:space:]]{#SNMPVALUE}[[:space:]].[[:space:]][a-zA-Z]+[[:space:]]$”]<p>Update: 0</p><p>LLD</p> | ||
OSPF Interface “{SNMPVALUE}” State | <p>-</p> | SNMP trap |
snmptrap[“ospfIfStateChange.+ospfIfIpAddress[[:space:]]{#SNMPVALUE}[[:space:]].+ospfIfState[[:space:]][a-zA-Z]+”]<p>Update: 0</p><p>LLD</p> |
Name | Description | Expression | Priority | ||
---|---|---|---|---|---|
BGP Peer “{#SNMPINDEX}”->”{#SNMPVALUE}” State changed | <p>-</p> | <p>Expression: nodata(/Template Cisco General/snmptrap[“(bgpEstablished | bgpBackwardTransition | cbgpFsmStateChange).*bgpPeerState .{#SNMPINDEX}[[:space:]][a-zA-Z]+[[:space:]]”],10m)=0</p><p>Recovery expression: </p> | average |
BGP Peer “{#SNMPINDEX}”->”{#SNMPVALUE}” State changed | <p>-</p> | <p>Expression: nodata(/Template Cisco General/snmptrap[“(bgpBackwardTransition | cbgpFsmStateChange).*bgpPeerState .{#SNMPINDEX}[[:space:]][a-zA-Z]+[[:space:]]”],10m)=0</p><p>Recovery expression: </p> | average | |
OSPF Interface “{#SNMPVALUE}” State has been changed | <p>-</p> | <p>Expression: nodata(/Template Cisco General/snmptrap[“ospfIfStateChange.+ospfIfIpAddress[[:space:]]{#SNMPVALUE}[[:space:]].+ospfIfState[[:space:]][a-zA-Z]+”],10m)=0</p><p>Recovery expression: </p> | average | ||
OSPF Neighbor {#SNMPVALUE} has been changed | <p>-</p> | <p>Expression: nodata(/Template Cisco General/snmptrap[“(ospfNbrStateChange).ospfNbrIpAddr[[:space:]]{#SNMPVALUE}[[:space:]].[[:space:]][a-zA-Z]+[[:space:]]$”],10m)=0</p><p>Recovery expression: </p> | average | ||
BGP Peer “{#SNMPINDEX}”->”{#SNMPVALUE}” State changed (LLD) | <p>-</p> | <p>Expression: nodata(/Template Cisco General/snmptrap[“(bgpEstablished | bgpBackwardTransition | cbgpFsmStateChange).*bgpPeerState .{#SNMPINDEX}[[:space:]][a-zA-Z]+[[:space:]]”],10m)=0</p><p>Recovery expression: </p> | average |
BGP Peer “{#SNMPINDEX}”->”{#SNMPVALUE}” State changed (LLD) | <p>-</p> | <p>Expression: nodata(/Template Cisco General/snmptrap[“(bgpBackwardTransition | cbgpFsmStateChange).*bgpPeerState .{#SNMPINDEX}[[:space:]][a-zA-Z]+[[:space:]]”],10m)=0</p><p>Recovery expression: </p> | average | |
OSPF Neighbor {#SNMPVALUE} has been changed (LLD) | <p>-</p> | <p>Expression: nodata(/Template Cisco General/snmptrap[“(ospfNbrStateChange).ospfNbrIpAddr[[:space:]]{#SNMPVALUE}[[:space:]].[[:space:]][a-zA-Z]+[[:space:]]$”],10m)=0</p><p>Recovery expression: </p> | average | ||
OSPF Interface “{#SNMPVALUE}” State has been changed (LLD) | <p>-</p> | <p>Expression: nodata(/Template Cisco General/snmptrap[“ospfIfStateChange.+ospfIfIpAddress[[:space:]]{#SNMPVALUE}[[:space:]].+ospfIfState[[:space:]][a-zA-Z]+”],10m)=0</p><p>Recovery expression: </p> | average |
There are no macros links in this template.
Name |
---|
Template Cisco General |
Template_Cisco_Traps |
Name | Description | Type | Key and additional info |
---|---|---|---|
CPU | <p>CISCO-PROCESS-MIB::cpmCPUTotalPhysicalIndex The entPhysicalIndex of the physical entity for which the CPU statistics in this entry are maintained. The physical entity can be a CPU chip, a group of CPUs, a CPU card etc. The exact type of this entity is described by its entPhysicalVendorType value. If the CPU statistics in this entry correspond to more than one physical entity (or to no physical entity), or if the entPhysicalTable is not supported on the SNMP agent, the value of this object must be zero.</p> | SNMP agent |
cpmCPUTotalPhysicalIndex<p>Update: 300</p> |
$1 Sensors | <p>The textual name of the physical entity.</p> | SNMP agent |
entPhysicalName[Voltage]<p>Update: 300</p> |
$1 Sensors | <p>The textual name of the physical entity.</p> | SNMP agent |
entPhysicalName[“Fan Tray”]<p>Update: 300</p> |
Temperature Sensors | <p>CISCO-ENVMON-MIB::ciscoEnvMonTemperatureStatusDescr Textual description of the testpoint being instrumented.</p> | SNMP agent |
ciscoEnvMonTemperatureStatusDescr<p>Update: 300</p> |
OSPF Neighbors | <p>OSPF-MIB::ospfNbrIpAddr The IP address this neighbor is using in its IP source address. Note that, on addressless links, this will not be 0.0.0.0 but the address of another of the neighbor’s interfaces.</p> | SNMP agent |
ospfNbrIpAddr<p>Update: 300</p> |
$1 Sensors | <p>The textual name of the physical entity.</p> | SNMP agent |
entPhysicalName[“Power”]<p>Update: 300</p> |
OSPF Interfaces | <p>OSPF-MIB::ospfIfIpAddress The IP address of this OSPF interface.</p> | SNMP agent |
ospfIfIpAddress<p>Update: 300</p> |
BGP Peers | <p>BGP4-MIB::bgpPeerIdentifier</p> | SNMP agent |
bgpPeerIdentifier<p>Update: 300</p> |
Memory Pool | <p>CISCO-MEMORY-POOL-MIB::ciscoMemoryPoolName A textual name assigned to the memory pool.</p> | SNMP agent |
ciscoMemoryPoolName<p>Update: 300</p> |
FAN | <p>CISCO-ENVMON-MIB::ciscoEnvMonFanStatusDescr Textual description of the fan being instrumented.</p> | SNMP agent |
ciscoEnvMonFanStatusDescr<p>Update: 300</p> |
$1 Sensors | <p>The textual name of the physical entity.</p> | SNMP agent |
entPhysicalName[Module]<p>Update: 300</p> |
Power Supplies | <p>CISCO-ENVMON-MIB::ciscoEnvMonSupplyStatusDescr Textual description of the power supply being instrumented.</p> | SNMP agent |
ciscoEnvMonSupplyStatusDescr<p>Update: 300</p> |
$1 Sensors | <p>The textual name of the physical entity.</p> | SNMP agent |
entPhysicalName[Amperage]<p>Update: 300</p> |
Name | Description | Type | Key and additional info | |||
---|---|---|---|---|---|---|
snmptrap (IF Down) | <p>-</p> | SNMP trap |
snmptrap[.1.3.6.1.6.3.1.1.5.3]<p>Update: 0</p> | |||
snmptrap (IF Up) | <p>-</p> | SNMP trap |
snmptrap[.1.3.6.1.6.3.1.1.5.4]<p>Update: 0</p> | |||
snmptrap (OSPF Neighbor Up/Down) | <p>-</p> | SNMP trap |
snmptrap[1.3.6.1.2.1.14.16.2.2]<p>Update: 0</p> | |||
snmptrap (BGP Neighbor Up/Down) | <p>-</p> | SNMP trap |
snmptrap[1.3.6.1.2.1.15.3.1.2 | 1.3.6.1.4.1.9.9.187.1.2.5.1.3]<p>Update: 0</p> | ||
CPU Usage 1min Rev ({#SNMPINDEX}) | <p>CISCO-PROCESS-MIB::cpmCPUTotal1minRev The overall CPU busy percentage in the last 1 minute period. This object deprecates the object cpmCPUTotal1min and increases the value range to (0..100).</p> | SNMP agent |
cpmCPUTotal1minRev[{#SNMPINDEX}]<p>Update: 60</p><p>LLD</p> | |||
CPU Usage 5min Rev ({#SNMPINDEX}) | <p>CISCO-PROCESS-MIB::cpmCPUTotal5minRev The overall CPU busy percentage in the last 5 minute period. This object deprecates the object cpmCPUTotal5min and increases the value range to (0..100).</p> | SNMP agent |
cpmCPUTotal5minRev[{#SNMPINDEX}]<p>Update: 300</p><p>LLD</p> | |||
CPU Usage 5sec Rev ({#SNMPINDEX}) | <p>CISCO-PROCESS-MIB::cpmCPUTotal5secRev The overall CPU busy percentage in the last 5 second period. This object deprecates the object cpmCPUTotal5sec and increases the value range to (0..100). This object is deprecated by cpmCPUTotalMonIntervalValue.</p> | SNMP agent |
cpmCPUTotal5secRev[{#SNMPINDEX}]<p>Update: 30</p><p>LLD</p> | |||
$2 on Sensor “$1” | <p>CISCO-ENTITY-SENSOR-MIB::entSensorValue This variable reports the most recent measurement seen by the sensor.</p> | SNMP agent |
entSensorValue[”{#SNMPVALUE}”,Voltage]<p>Update: 60</p><p>LLD</p> | |||
Status of $2 Sensor “$1” | <p>CISCO-ENTITY-SENSOR-MIB::entSensorStatus This variable indicates the present operational status of the sensor.</p> | SNMP agent |
entSensorStatus[”{#SNMPVALUE}”,Voltage]<p>Update: 60</p><p>LLD</p> | |||
Manufacturer of $2 “$1” | <p>ENTITY-MIB::entPhysicalMfgName The name of the manufacturer of this physical component. The preferred value is the manufacturer name string actually printed on the component itself (if present).</p> | SNMP agent |
entPhysicalMfgName[”{#SNMPVALUE}”,”Fan Tray”]<p>Update: 86400</p><p>LLD</p> | |||
Model Name of $2 “$1” | <p>ENTITY-MIB::entPhysicalModelName The vendor-specific model name identifier string associated with this physical component. The preferred value is the customer-visible part number, which may be printed on the component itself.</p> | SNMP agent |
entPhysicalModelName[”{#SNMPVALUE}”,”Fan Tray”]<p>Update: 86400</p><p>LLD</p> | |||
Operational Status of $2 “$1” | <p>CISCO-ENTITY-FRU-CONTROL-MIB::cefcFanTrayOperStatus The operational state of the fan or fan tray.</p> | SNMP agent |
cefcFanTrayOperStatus[”{#SNMPVALUE}”,”Fan Tray”]<p>Update: 60</p><p>LLD</p> | |||
Serial Number of $2 “$1” | <p>ENTITY-MIB::entPhysicalSerialNum The vendor-specific serial number string for the physical entity. The preferred value is the serial number string actually printed on the component itself (if present).</p> | SNMP agent |
entPhysicalSerialNum[”{#SNMPVALUE}”,”Fan Tray”]<p>Update: 3600</p><p>LLD</p> | |||
SNMP traps for “{#SNMPVALUE}” sensor | <p>-</p> | SNMP trap |
snmptrap[“ciscoEnvMonTemperatureState.{#SNMPINDEX}[[:space:]](warning | critical | shutdown | normal)”]<p>Update: 0</p><p>LLD</p> |
Status of Temperature Sensor “$1” | <p>CISCO-ENVMON-MIB::ciscoEnvMonTemperatureState The current state of the testpoint being instrumented.</p> | SNMP agent |
ciscoEnvMonTemperatureState[”{#SNMPVALUE}”]<p>Update: 60</p><p>LLD</p> | |||
Temperature on Sensor “$1” | <p>CISCO-ENVMON-MIB::ciscoEnvMonTemperatureStatusValue The current measurement of the testpoint being instrumented.</p> | SNMP agent |
ciscoEnvMonTemperatureStatusValue[”{#SNMPVALUE}”]<p>Update: 60</p><p>LLD</p> | |||
Threshold Temperature on Sensor “$1” | <p>CISCO-ENVMON-MIB::ciscoEnvMonTemperatureThreshold The highest value that the associated instance of the object ciscoEnvMonTemperatureStatusValue may obtain before an emergency shutdown of the managed device is initiated.</p> | SNMP agent |
ciscoEnvMonTemperatureThreshold[”{#SNMPVALUE}”]<p>Update: 1800</p><p>LLD</p> | |||
OSPF “{#SNMPVALUE}” Neighbour State | <p>-</p> | SNMP trap |
snmptrap[“(ospfNbrStateChange).ospfNbrIpAddr[[:space:]]{#SNMPVALUE}[[:space:]].[[:space:]][a-zA-Z]+[[:space:]]$”]<p>Update: 0</p><p>LLD</p> | |||
Status of $2 Sensor “$1” | <p>CISCO-ENTITY-SENSOR-MIB::entSensorStatus This variable indicates the present operational status of the sensor.</p> | SNMP agent |
entSensorStatus[”{#SNMPVALUE}”,Power]<p>Update: 60</p><p>LLD</p> | |||
Value of $2 Sensor “$1” | <p>CISCO-ENTITY-SENSOR-MIB::entSensorValue This variable reports the most recent measurement seen by the sensor.</p> | SNMP agent |
entSensorValue[”{#SNMPVALUE}”,Power]<p>Update: 60</p><p>LLD</p> | |||
OSPF Interface “{SNMPVALUE}” State | <p>-</p> | SNMP trap |
snmptrap[“ospfIfStateChange.+ospfIfIpAddress[[:space:]]{#SNMPVALUE}[[:space:]].+ospfIfState[[:space:]][a-zA-Z]+”]<p>Update: 0</p><p>LLD</p> | |||
BGP Peer “{#SNMPINDEX}” State | <p>-</p> | SNMP trap |
snmptrap[“(bgpEstablished | bgpBackwardTransition | cbgpFsmStateChange).*bgpPeerState.{#SNMPINDEX}[[:space:]][a-zA-Z]+[[:space:]]”]<p>Update: 0</p><p>LLD</p> | |
BGP Peer “{#SNMPINDEX}” State | <p>-</p> | SNMP trap |
snmptrap[“(bgpBackwardTransition | cbgpFsmStateChange).*bgpPeerState.{#SNMPINDEX}[[:space:]][a-zA-Z]+[[:space:]]”]<p>Update: 0</p><p>LLD</p> | ||
Free memory on Memory Pool “$1” | <p>CISCO-MEMORY-POOL-MIB::ciscoMemoryPoolFree Indicates the number of bytes from the memory pool that are currently unused on the managed device.</p> | SNMP agent |
ciscoMemoryPoolFree[”{#SNMPVALUE}”]<p>Update: 60</p><p>LLD</p> | |||
Name of Memory Pool “$1” | <p>CISCO-MEMORY-POOL-MIB::ciscoMemoryPoolName A textual name assigned to the memory pool.</p> | SNMP agent |
ciscoMemoryPoolName[”{#SNMPVALUE}”]<p>Update: 3600</p><p>LLD</p> | |||
Total Memory Pool “$1” | <p>-</p> | Calculated |
ciscoMemoryPoolTotal[”{#SNMPVALUE}”]<p>Update: 3600</p><p>LLD</p> | |||
Used memory on Memory Pool “$1” | <p>CISCO-MEMORY-POOL-MIB::ciscoMemoryPoolUsed Indicates the number of bytes from the memory pool that are currently in use by applications on the managed device.</p> | SNMP agent |
ciscoMemoryPoolUsed[”{#SNMPVALUE}”]<p>Update: 300</p><p>LLD</p> | |||
Status of FAN “$1” | <p>CISCO-ENVMON-MIB::ciscoEnvMonFanState The current state of the fan being instrumented.</p> | SNMP agent |
ciscoEnvMonFanState[”{#SNMPVALUE}”]<p>Update: 60</p><p>LLD</p> | |||
Manufacturer of $2 “$1” | <p>ENTITY-MIB::entPhysicalMfgName The name of the manufacturer of this physical component. The preferred value is the manufacturer name string actually printed on the component itself (if present).</p> | SNMP agent |
entPhysicalMfgName[”{#SNMPVALUE}”,”Module”]<p>Update: 86400</p><p>LLD</p> | |||
Model Name of $2 “$1” | <p>ENTITY-MIB::entPhysicalModelName The vendor-specific model name identifier string associated with this physical component. The preferred value is the customer-visible part number, which may be printed on the component itself.</p> | SNMP agent |
entPhysicalModelName[”{#SNMPVALUE}”,”Module”]<p>Update: 86400</p><p>LLD</p> | |||
Operational Status of $2 “$1” | <p>ENTITY-STATE-MIB::entStateOper The operational state for this entity.</p> | SNMP agent |
entStateOper[”{#SNMPVALUE}”,”Module”]<p>Update: 60</p><p>LLD</p> | |||
Serial Number of $2 “$1” | <p>ENTITY-MIB::entPhysicalSerialNum The vendor-specific serial number string for the physical entity. The preferred value is the serial number string actually printed on the component itself (if present).</p> | SNMP agent |
entPhysicalSerialNum[”{#SNMPVALUE}”,”Module”]<p>Update: 3600</p><p>LLD</p> | |||
Status of Power Supply “$1” | <p>CISCO-ENVMON-MIB::ciscoEnvMonSupplyState The current state of the power supply being instrumented.</p> | SNMP agent |
ciscoEnvMonSupplyState[”{#SNMPVALUE}”]<p>Update: 60</p><p>LLD</p> | |||
$2 of Sensor “$1” | <p>CISCO-ENTITY-SENSOR-MIB::entSensorValue This variable reports the most recent measurement seen by the sensor.</p> | SNMP agent |
entSensorValue[”{#SNMPVALUE}”,Amperage]<p>Update: 60</p><p>LLD</p> | |||
Status of $2 Sensor “$1” | <p>CISCO-ENTITY-SENSOR-MIB::entSensorStatus This variable indicates the present operational status of the sensor.</p> | SNMP agent |
entSensorStatus[”{#SNMPVALUE}”,Amperage]<p>Update: 60</p><p>LLD</p> |
Name | Description | Expression | Priority | ||
---|---|---|---|---|---|
BGP Peer “{#SNMPINDEX}”->”{#SNMPVALUE}” State changed | <p>-</p> | <p>Expression: nodata(/Cisco_6500/snmptrap[“(bgpEstablished | bgpBackwardTransition | cbgpFsmStateChange).*bgpPeerState .{#SNMPINDEX}[[:space:]][a-zA-Z]+[[:space:]]”],10m)=0</p><p>Recovery expression: </p> | average |
BGP Peer “{#SNMPINDEX}”->”{#SNMPVALUE}” State changed | <p>-</p> | <p>Expression: nodata(/Cisco_6500/snmptrap[“(bgpBackwardTransition | cbgpFsmStateChange).*bgpPeerState .{#SNMPINDEX}[[:space:]][a-zA-Z]+[[:space:]]”],10m)=0</p><p>Recovery expression: </p> | average | |
OSPF Interface “{#SNMPVALUE}” State has been changed | <p>-</p> | <p>Expression: nodata(/Cisco_6500/snmptrap[“ospfIfStateChange.+ospfIfIpAddress[[:space:]]{#SNMPVALUE}[[:space:]].+ospfIfState[[:space:]][a-zA-Z]+”],10m)=0</p><p>Recovery expression: </p> | average | ||
OSPF Neighbor {#SNMPVALUE} has been changed | <p>-</p> | <p>Expression: nodata(/Cisco_6500/snmptrap[“(ospfNbrStateChange).ospfNbrIpAddr[[:space:]]{#SNMPVALUE}[[:space:]].[[:space:]][a-zA-Z]+[[:space:]]$”],10m)=0</p><p>Recovery expression: </p> | average | ||
Power Sensor “{#SNMPVALUE}” is nonoperational | <p>-</p> | <p>Expression: last(/Cisco_6500/entSensorStatus[”{#SNMPVALUE}”,Power])=3</p><p>Recovery expression: </p> | high | ||
Power Sensor “{#SNMPVALUE}” is unavailable | <p>-</p> | <p>Expression: last(/Cisco_6500/entSensorStatus[”{#SNMPVALUE}”,Power])=2</p><p>Recovery expression: </p> | average | ||
Amperage Sensor “{#SNMPVALUE}” is nonoperational | <p>-</p> | <p>Expression: last(/Cisco_6500/entSensorStatus[”{#SNMPVALUE}”,Amperage])=3</p><p>Recovery expression: </p> | high | ||
Amperage Sensor “{#SNMPVALUE}” is unavailable | <p>-</p> | <p>Expression: last(/Cisco_6500/entSensorStatus[”{#SNMPVALUE}”,Amperage])=2</p><p>Recovery expression: </p> | average | ||
Module “{#SNMPVALUE}” is inoperable | <p>-</p> | <p>Expression: last(/Cisco_6500/entStateOper[”{#SNMPVALUE}”,”Module”])=2</p><p>Recovery expression: </p> | disaster | ||
Voltage Sensor “{#SNMPVALUE}” is nonoperational | <p>-</p> | <p>Expression: last(/Cisco_6500/entSensorStatus[”{#SNMPVALUE}”,Voltage])=3</p><p>Recovery expression: </p> | high | ||
Voltage Sensor “{#SNMPVALUE}” is unavailable | <p>-</p> | <p>Expression: last(/Cisco_6500/entSensorStatus[”{#SNMPVALUE}”,Voltage])=2</p><p>Recovery expression: </p> | average | ||
Status of Fan Tray “{#SNMPVALUE}” is in partial failure | <p>-</p> | <p>Expression: last(/Cisco_6500/cefcFanTrayOperStatus[”{#SNMPVALUE}”,”Fan Tray”])=4</p><p>Recovery expression: </p> | warning | ||
Status of Fan Tray “{#SNMPVALUE}” is powered down | <p>-</p> | <p>Expression: last(/Cisco_6500/cefcFanTrayOperStatus[”{#SNMPVALUE}”,”Fan Tray”])=3</p><p>Recovery expression: </p> | high | ||
High CPU #{#SNMPINDEX} Usage | <p>-</p> | <p>Expression: last(/Cisco_6500/cpmCPUTotal5minRev[{#SNMPINDEX}])>95</p><p>Recovery expression: </p> | high | ||
Status of FAN “{#SNMPVALUE}” is critical | <p>-</p> | <p>Expression: last(/Cisco_6500/ciscoEnvMonFanState[”{#SNMPVALUE}”])=3</p><p>Recovery expression: </p> | average | ||
Status of FAN “{#SNMPVALUE}” is non-operable | <p>-</p> | <p>Expression: last(/Cisco_6500/ciscoEnvMonFanState[”{#SNMPVALUE}”])=2</p><p>Recovery expression: </p> | warning | ||
Status of FAN “{#SNMPVALUE}” is not functioning | <p>-</p> | <p>Expression: last(/Cisco_6500/ciscoEnvMonFanState[”{#SNMPVALUE}”])=6</p><p>Recovery expression: </p> | average | ||
Status of FAN “{#SNMPVALUE}” is shutdown | <p>-</p> | <p>Expression: last(/Cisco_6500/ciscoEnvMonFanState[”{#SNMPVALUE}”])=4</p><p>Recovery expression: </p> | high | ||
High utilization of Memory Pool “{#SNMPVALUE}” | <p>-</p> | <p>Expression: last(/Cisco_6500/ciscoMemoryPoolUsed[”{#SNMPVALUE}”])>last(/Cisco_6500/ciscoMemoryPoolTotal[”{#SNMPVALUE}”])*0.9</p><p>Recovery expression: </p> | average | ||
Status of Power Supply “{#SNMPVALUE}” is critical | <p>-</p> | <p>Expression: last(/Cisco_6500/ciscoEnvMonSupplyState[”{#SNMPVALUE}”])=3</p><p>Recovery expression: </p> | average | ||
Status of Power Supply “{#SNMPVALUE}” is non-operable | <p>-</p> | <p>Expression: last(/Cisco_6500/ciscoEnvMonSupplyState[”{#SNMPVALUE}”])=2</p><p>Recovery expression: </p> | warning | ||
Status of Power Supply “{#SNMPVALUE}” is not functioning | <p>-</p> | <p>Expression: last(/Cisco_6500/ciscoEnvMonSupplyState[”{#SNMPVALUE}”])=6</p><p>Recovery expression: </p> | average | ||
Status of Power Supply “{#SNMPVALUE}” is shutdown | <p>-</p> | <p>Expression: last(/Cisco_6500/ciscoEnvMonSupplyState[”{#SNMPVALUE}”])=4</p><p>Recovery expression: </p> | high | ||
Temperature Sensor “{#SNMPVALUE}” is abnormal | <p>-</p> | <p>Expression: last(/Cisco_6500/ciscoEnvMonTemperatureState[”{#SNMPVALUE}”])=2</p><p>Recovery expression: </p> | warning | ||
Temperature Sensor “{#SNMPVALUE}” is abnormal | <p>-</p> | <p>Expression: last(/Cisco_6500/ciscoEnvMonTemperatureState[”{#SNMPVALUE}”])=3</p><p>Recovery expression: </p> | high | ||
Temperature Sensor “{#SNMPVALUE}” is not functioning | <p>-</p> | <p>Expression: last(/Cisco_6500/ciscoEnvMonTemperatureState[”{#SNMPVALUE}”])=6</p><p>Recovery expression: </p> | information | ||
Temperature Sensor “{#SNMPVALUE}” is shutdown | <p>-</p> | <p>Expression: last(/Cisco_6500/ciscoEnvMonTemperatureState[”{#SNMPVALUE}”])=4</p><p>Recovery expression: </p> | disaster | ||
High CPU #{#SNMPINDEX} Usage (LLD) | <p>-</p> | <p>Expression: last(/Cisco_6500/cpmCPUTotal5minRev[{#SNMPINDEX}])>95</p><p>Recovery expression: </p> | high | ||
Voltage Sensor “{#SNMPVALUE}” is nonoperational (LLD) | <p>-</p> | <p>Expression: last(/Cisco_6500/entSensorStatus[”{#SNMPVALUE}”,Voltage])=3</p><p>Recovery expression: </p> | high | ||
Voltage Sensor “{#SNMPVALUE}” is unavailable (LLD) | <p>-</p> | <p>Expression: last(/Cisco_6500/entSensorStatus[”{#SNMPVALUE}”,Voltage])=2</p><p>Recovery expression: </p> | average | ||
Status of Fan Tray “{#SNMPVALUE}” is in partial failure (LLD) | <p>-</p> | <p>Expression: last(/Cisco_6500/cefcFanTrayOperStatus[”{#SNMPVALUE}”,”Fan Tray”])=4</p><p>Recovery expression: </p> | warning | ||
Status of Fan Tray “{#SNMPVALUE}” is powered down (LLD) | <p>-</p> | <p>Expression: last(/Cisco_6500/cefcFanTrayOperStatus[”{#SNMPVALUE}”,”Fan Tray”])=3</p><p>Recovery expression: </p> | high | ||
Temperature Sensor “{#SNMPVALUE}” is abnormal (LLD) | <p>-</p> | <p>Expression: last(/Cisco_6500/ciscoEnvMonTemperatureState[”{#SNMPVALUE}”])=2</p><p>Recovery expression: </p> | warning | ||
Temperature Sensor “{#SNMPVALUE}” is abnormal (LLD) | <p>-</p> | <p>Expression: last(/Cisco_6500/ciscoEnvMonTemperatureState[”{#SNMPVALUE}”])=3</p><p>Recovery expression: </p> | high | ||
Temperature Sensor “{#SNMPVALUE}” is not functioning (LLD) | <p>-</p> | <p>Expression: last(/Cisco_6500/ciscoEnvMonTemperatureState[”{#SNMPVALUE}”])=6</p><p>Recovery expression: </p> | information | ||
Temperature Sensor “{#SNMPVALUE}” is shutdown (LLD) | <p>-</p> | <p>Expression: last(/Cisco_6500/ciscoEnvMonTemperatureState[”{#SNMPVALUE}”])=4</p><p>Recovery expression: </p> | disaster | ||
OSPF Neighbor {#SNMPVALUE} has been changed (LLD) | <p>-</p> | <p>Expression: nodata(/Cisco_6500/snmptrap[“(ospfNbrStateChange).ospfNbrIpAddr[[:space:]]{#SNMPVALUE}[[:space:]].[[:space:]][a-zA-Z]+[[:space:]]$”],10m)=0</p><p>Recovery expression: </p> | average | ||
Power Sensor “{#SNMPVALUE}” is nonoperational (LLD) | <p>-</p> | <p>Expression: last(/Cisco_6500/entSensorStatus[”{#SNMPVALUE}”,Power])=3</p><p>Recovery expression: </p> | high | ||
Power Sensor “{#SNMPVALUE}” is unavailable (LLD) | <p>-</p> | <p>Expression: last(/Cisco_6500/entSensorStatus[”{#SNMPVALUE}”,Power])=2</p><p>Recovery expression: </p> | average | ||
OSPF Interface “{#SNMPVALUE}” State has been changed (LLD) | <p>-</p> | <p>Expression: nodata(/Cisco_6500/snmptrap[“ospfIfStateChange.+ospfIfIpAddress[[:space:]]{#SNMPVALUE}[[:space:]].+ospfIfState[[:space:]][a-zA-Z]+”],10m)=0</p><p>Recovery expression: </p> | average | ||
BGP Peer “{#SNMPINDEX}”->”{#SNMPVALUE}” State changed (LLD) | <p>-</p> | <p>Expression: nodata(/Cisco_6500/snmptrap[“(bgpEstablished | bgpBackwardTransition | cbgpFsmStateChange).*bgpPeerState .{#SNMPINDEX}[[:space:]][a-zA-Z]+[[:space:]]”],10m)=0</p><p>Recovery expression: </p> | average |
BGP Peer “{#SNMPINDEX}”->”{#SNMPVALUE}” State changed (LLD) | <p>-</p> | <p>Expression: nodata(/Cisco_6500/snmptrap[“(bgpBackwardTransition | cbgpFsmStateChange).*bgpPeerState .{#SNMPINDEX}[[:space:]][a-zA-Z]+[[:space:]]”],10m)=0</p><p>Recovery expression: </p> | average | |
High utilization of Memory Pool “{#SNMPVALUE}” (LLD) | <p>-</p> | <p>Expression: last(/Cisco_6500/ciscoMemoryPoolUsed[”{#SNMPVALUE}”])>last(/Cisco_6500/ciscoMemoryPoolTotal[”{#SNMPVALUE}”])*0.9</p><p>Recovery expression: </p> | average | ||
Status of FAN “{#SNMPVALUE}” is critical (LLD) | <p>-</p> | <p>Expression: last(/Cisco_6500/ciscoEnvMonFanState[”{#SNMPVALUE}”])=3</p><p>Recovery expression: </p> | average | ||
Status of FAN “{#SNMPVALUE}” is non-operable (LLD) | <p>-</p> | <p>Expression: last(/Cisco_6500/ciscoEnvMonFanState[”{#SNMPVALUE}”])=2</p><p>Recovery expression: </p> | warning | ||
Status of FAN “{#SNMPVALUE}” is not functioning (LLD) | <p>-</p> | <p>Expression: last(/Cisco_6500/ciscoEnvMonFanState[”{#SNMPVALUE}”])=6</p><p>Recovery expression: </p> | average | ||
Status of FAN “{#SNMPVALUE}” is shutdown (LLD) | <p>-</p> | <p>Expression: last(/Cisco_6500/ciscoEnvMonFanState[”{#SNMPVALUE}”])=4</p><p>Recovery expression: </p> | high | ||
Module “{#SNMPVALUE}” is inoperable (LLD) | <p>-</p> | <p>Expression: last(/Cisco_6500/entStateOper[”{#SNMPVALUE}”,”Module”])=2</p><p>Recovery expression: </p> | disaster | ||
Status of Power Supply “{#SNMPVALUE}” is critical (LLD) | <p>-</p> | <p>Expression: last(/Cisco_6500/ciscoEnvMonSupplyState[”{#SNMPVALUE}”])=3</p><p>Recovery expression: </p> | average | ||
Status of Power Supply “{#SNMPVALUE}” is non-operable (LLD) | <p>-</p> | <p>Expression: last(/Cisco_6500/ciscoEnvMonSupplyState[”{#SNMPVALUE}”])=2</p><p>Recovery expression: </p> | warning | ||
Status of Power Supply “{#SNMPVALUE}” is not functioning (LLD) | <p>-</p> | <p>Expression: last(/Cisco_6500/ciscoEnvMonSupplyState[”{#SNMPVALUE}”])=6</p><p>Recovery expression: </p> | average | ||
Status of Power Supply “{#SNMPVALUE}” is shutdown (LLD) | <p>-</p> | <p>Expression: last(/Cisco_6500/ciscoEnvMonSupplyState[”{#SNMPVALUE}”])=4</p><p>Recovery expression: </p> | high | ||
Amperage Sensor “{#SNMPVALUE}” is nonoperational (LLD) | <p>-</p> | <p>Expression: last(/Cisco_6500/entSensorStatus[”{#SNMPVALUE}”,Amperage])=3</p><p>Recovery expression: </p> | high | ||
Amperage Sensor “{#SNMPVALUE}” is unavailable (LLD) | <p>-</p> | <p>Expression: last(/Cisco_6500/entSensorStatus[”{#SNMPVALUE}”,Amperage])=2</p><p>Recovery expression: </p> | average |
There are no macros links in this template.
There are no template links in this template.
There are no discovery rules in this template.
Name | Description | Type | Key and additional info | |
---|---|---|---|---|
Type of remote session | <p>-</p> | SNMP trap |
snmptrap[“tslineSesType”]<p>Update: 0</p> | |
LSA has been originated | <p>OSPF-TRAP-MIB::ospfOriginateLsa</p> | SNMP trap |
snmptrap[“ospfOriginateLsa”]<p>Update: 0</p> | |
Attack Filter changes | <p>The system generates this notification to indicate that the cscaFilterStatus of the attack filter for cscaType has changed due to the reason determined by cscaDescription. The system limits the generation of this notifications for the same cscaType to a five-second interval.</p> | SNMP trap |
snmptrap[“cscaFilterChange”]<p>Update: 0</p> | |
Status of Attack Filter | <p>-</p> | SNMP trap |
snmptrap[“cscaFilterStatus”]<p>Update: 0</p> | |
SSH Sessions | <p>CISCO-SECURE-SHELL-MIB::cssSessionHostAddr</p> | SNMP trap |
snmptrap[“cssSessionHostAddr”]<p>Update: 0</p> | |
Source of Command | <p>-</p> | SNMP trap |
snmptrap[“ccmHistoryEventCommandSource”]<p>Update: 0</p> | |
OSPF Interface State | <p>OSPF-MIB::ospfIfState The OSPF Interface State.</p> | SNMP trap |
snmptrap[“ospfIfState”]<p>Update: 0</p> | |
BGP Peer State | <p>BGP4-MIB::bgpPeerState CISCO-BGP4-MIB::cbgpPeer2State The BGP peer connection state.</p> | SNMP trap |
snmptrap[“bgpPeerState | cbgpPeer2State”]<p>Update: 0</p> |
MPLS L3 State | <p>MPLS-L3VPN-STD-MIB::mplsL3VpnVrfUp MPLS-L3VPN-STD-MIB::mplsL3VpnVrfDown</p> | SNMP trap |
snmptrap[“mplsL3VpnVrf[Up | Down]”]<p>Update: 0</p> |
LSA aged to MaxAge | <p>-</p> | SNMP trap |
snmptrap[“ospfMaxAgeLsa”]<p>Update: 0</p> | |
OSP TX Retransmits | <p>-</p> | SNMP trap |
snmptrap[“ospfTxRetransmit”]<p>Update: 0</p> | |
OSPF neighbour state | <p>1 : down 2 : attempt 3 : init 4 : twoWay 5 : exchangeStart 6 : exchange 7 : loading 8 : full</p> | SNMP trap |
snmptrap[“ospfNbrStateChange.*ospfNbrState[[:space:]]”]<p>Update: 0</p> | |
BFD Sessions | <p>CISCO-IETF-BFD-MIB::ciscoBfdSessDown and ciscoBfdSessUp</p> | SNMP trap |
snmptrap[“ciscoBfdSess(Up | Down)”]<p>Update: 0</p> |
There are no triggers in this template.
There are no macros links in this template.
There are no template links in this template.
Name | Description | Type | Key and additional info |
---|---|---|---|
BGP Peers | <p>BGP4-MIB::bgpPeerIdentifier</p> | SNMP agent |
bgpPeerIdentifier<p>Update: 300</p> |
OSPF Neighbors | <p>OSPF-MIB::ospfNbrIpAddr The IP address this neighbor is using in its IP source address. Note that, on addressless links, this will not be 0.0.0.0 but the address of another of the neighbor’s interfaces.</p> | SNMP agent |
ospfNbrIpAddr<p>Update: 300</p> |
OSPF Interfaces | <p>OSPF-MIB::ospfIfIpAddress The IP address of this OSPF interface.</p> | SNMP agent |
ospfIfIpAddress<p>Update: 300</p> |
Name | Description | Type | Key and additional info | ||
---|---|---|---|---|---|
BGP Peer “{#SNMPINDEX}” State | <p>-</p> | SNMP trap |
snmptrap[“(bgpEstablished | bgpBackwardTransition | cbgpFsmStateChange).*bgpPeerState.{#SNMPINDEX}[[:space:]][a-zA-Z]+[[:space:]]”]<p>Update: 0</p><p>LLD</p> |
BGP Peer “{#SNMPINDEX}” State | <p>-</p> | SNMP trap |
snmptrap[“(bgpBackwardTransition | cbgpFsmStateChange).*bgpPeerState.{#SNMPINDEX}[[:space:]][a-zA-Z]+[[:space:]]”]<p>Update: 0</p><p>LLD</p> | |
OSPF “{#SNMPVALUE}” Neighbour State | <p>-</p> | SNMP trap |
snmptrap[“(ospfNbrStateChange).ospfNbrIpAddr[[:space:]]{#SNMPVALUE}[[:space:]].[[:space:]][a-zA-Z]+[[:space:]]$”]<p>Update: 0</p><p>LLD</p> | ||
OSPF Interface “{SNMPVALUE}” State | <p>-</p> | SNMP trap |
snmptrap[“ospfIfStateChange.+ospfIfIpAddress[[:space:]]{#SNMPVALUE}[[:space:]].+ospfIfState[[:space:]][a-zA-Z]+”]<p>Update: 0</p><p>LLD</p> |
Name | Description | Expression | Priority | ||
---|---|---|---|---|---|
BGP Peer “{#SNMPINDEX}”->”{#SNMPVALUE}” State changed | <p>-</p> | <p>Expression: nodata(/Template Cisco General/snmptrap[“(bgpEstablished | bgpBackwardTransition | cbgpFsmStateChange).*bgpPeerState .{#SNMPINDEX}[[:space:]][a-zA-Z]+[[:space:]]”],10m)=0</p><p>Recovery expression: </p> | average |
BGP Peer “{#SNMPINDEX}”->”{#SNMPVALUE}” State changed | <p>-</p> | <p>Expression: nodata(/Template Cisco General/snmptrap[“(bgpBackwardTransition | cbgpFsmStateChange).*bgpPeerState .{#SNMPINDEX}[[:space:]][a-zA-Z]+[[:space:]]”],10m)=0</p><p>Recovery expression: </p> | average | |
OSPF Interface “{#SNMPVALUE}” State has been changed | <p>-</p> | <p>Expression: nodata(/Template Cisco General/snmptrap[“ospfIfStateChange.+ospfIfIpAddress[[:space:]]{#SNMPVALUE}[[:space:]].+ospfIfState[[:space:]][a-zA-Z]+”],10m)=0</p><p>Recovery expression: </p> | average | ||
OSPF Neighbor {#SNMPVALUE} has been changed | <p>-</p> | <p>Expression: nodata(/Template Cisco General/snmptrap[“(ospfNbrStateChange).ospfNbrIpAddr[[:space:]]{#SNMPVALUE}[[:space:]].[[:space:]][a-zA-Z]+[[:space:]]$”],10m)=0</p><p>Recovery expression: </p> | average | ||
BGP Peer “{#SNMPINDEX}”->”{#SNMPVALUE}” State changed (LLD) | <p>-</p> | <p>Expression: nodata(/Template Cisco General/snmptrap[“(bgpEstablished | bgpBackwardTransition | cbgpFsmStateChange).*bgpPeerState .{#SNMPINDEX}[[:space:]][a-zA-Z]+[[:space:]]”],10m)=0</p><p>Recovery expression: </p> | average |
BGP Peer “{#SNMPINDEX}”->”{#SNMPVALUE}” State changed (LLD) | <p>-</p> | <p>Expression: nodata(/Template Cisco General/snmptrap[“(bgpBackwardTransition | cbgpFsmStateChange).*bgpPeerState .{#SNMPINDEX}[[:space:]][a-zA-Z]+[[:space:]]”],10m)=0</p><p>Recovery expression: </p> | average | |
OSPF Neighbor {#SNMPVALUE} has been changed (LLD) | <p>-</p> | <p>Expression: nodata(/Template Cisco General/snmptrap[“(ospfNbrStateChange).ospfNbrIpAddr[[:space:]]{#SNMPVALUE}[[:space:]].[[:space:]][a-zA-Z]+[[:space:]]$”],10m)=0</p><p>Recovery expression: </p> | average | ||
OSPF Interface “{#SNMPVALUE}” State has been changed (LLD) | <p>-</p> | <p>Expression: nodata(/Template Cisco General/snmptrap[“ospfIfStateChange.+ospfIfIpAddress[[:space:]]{#SNMPVALUE}[[:space:]].+ospfIfState[[:space:]][a-zA-Z]+”],10m)=0</p><p>Recovery expression: </p> | average |
There are no macros links in this template.
Name |
---|
Template Cisco General |
Template_Cisco_Traps |
Name | Description | Type | Key and additional info |
---|---|---|---|
CPU | <p>CISCO-PROCESS-MIB::cpmCPUTotalPhysicalIndex The entPhysicalIndex of the physical entity for which the CPU statistics in this entry are maintained. The physical entity can be a CPU chip, a group of CPUs, a CPU card etc. The exact type of this entity is described by its entPhysicalVendorType value. If the CPU statistics in this entry correspond to more than one physical entity (or to no physical entity), or if the entPhysicalTable is not supported on the SNMP agent, the value of this object must be zero.</p> | SNMP agent |
cpmCPUTotalPhysicalIndex<p>Update: 300</p> |
$1 Sensors | <p>The textual name of the physical entity.</p> | SNMP agent |
entPhysicalName[Voltage]<p>Update: 300</p> |
$1 Sensors | <p>The textual name of the physical entity.</p> | SNMP agent |
entPhysicalName[“Fan Tray”]<p>Update: 300</p> |
Temperature Sensors | <p>CISCO-ENVMON-MIB::ciscoEnvMonTemperatureStatusDescr Textual description of the testpoint being instrumented.</p> | SNMP agent |
ciscoEnvMonTemperatureStatusDescr<p>Update: 300</p> |
OSPF Neighbors | <p>OSPF-MIB::ospfNbrIpAddr The IP address this neighbor is using in its IP source address. Note that, on addressless links, this will not be 0.0.0.0 but the address of another of the neighbor’s interfaces.</p> | SNMP agent |
ospfNbrIpAddr<p>Update: 300</p> |
$1 Sensors | <p>The textual name of the physical entity.</p> | SNMP agent |
entPhysicalName[“Power”]<p>Update: 300</p> |
OSPF Interfaces | <p>OSPF-MIB::ospfIfIpAddress The IP address of this OSPF interface.</p> | SNMP agent |
ospfIfIpAddress<p>Update: 300</p> |
BGP Peers | <p>BGP4-MIB::bgpPeerIdentifier</p> | SNMP agent |
bgpPeerIdentifier<p>Update: 300</p> |
Memory Pool | <p>CISCO-MEMORY-POOL-MIB::ciscoMemoryPoolName A textual name assigned to the memory pool.</p> | SNMP agent |
ciscoMemoryPoolName<p>Update: 300</p> |
FAN | <p>CISCO-ENVMON-MIB::ciscoEnvMonFanStatusDescr Textual description of the fan being instrumented.</p> | SNMP agent |
ciscoEnvMonFanStatusDescr<p>Update: 300</p> |
$1 Sensors | <p>The textual name of the physical entity.</p> | SNMP agent |
entPhysicalName[Module]<p>Update: 300</p> |
Power Supplies | <p>CISCO-ENVMON-MIB::ciscoEnvMonSupplyStatusDescr Textual description of the power supply being instrumented.</p> | SNMP agent |
ciscoEnvMonSupplyStatusDescr<p>Update: 300</p> |
$1 Sensors | <p>The textual name of the physical entity.</p> | SNMP agent |
entPhysicalName[Amperage]<p>Update: 300</p> |
Name | Description | Type | Key and additional info | |||
---|---|---|---|---|---|---|
snmptrap (IF Down) | <p>-</p> | SNMP trap |
snmptrap[.1.3.6.1.6.3.1.1.5.3]<p>Update: 0</p> | |||
snmptrap (IF Up) | <p>-</p> | SNMP trap |
snmptrap[.1.3.6.1.6.3.1.1.5.4]<p>Update: 0</p> | |||
snmptrap (OSPF Neighbor Up/Down) | <p>-</p> | SNMP trap |
snmptrap[1.3.6.1.2.1.14.16.2.2]<p>Update: 0</p> | |||
snmptrap (BGP Neighbor Up/Down) | <p>-</p> | SNMP trap |
snmptrap[1.3.6.1.2.1.15.3.1.2 | 1.3.6.1.4.1.9.9.187.1.2.5.1.3]<p>Update: 0</p> | ||
CPU Usage 1min Rev ({#SNMPINDEX}) | <p>CISCO-PROCESS-MIB::cpmCPUTotal1minRev The overall CPU busy percentage in the last 1 minute period. This object deprecates the object cpmCPUTotal1min and increases the value range to (0..100).</p> | SNMP agent |
cpmCPUTotal1minRev[{#SNMPINDEX}]<p>Update: 60</p><p>LLD</p> | |||
CPU Usage 5min Rev ({#SNMPINDEX}) | <p>CISCO-PROCESS-MIB::cpmCPUTotal5minRev The overall CPU busy percentage in the last 5 minute period. This object deprecates the object cpmCPUTotal5min and increases the value range to (0..100).</p> | SNMP agent |
cpmCPUTotal5minRev[{#SNMPINDEX}]<p>Update: 300</p><p>LLD</p> | |||
CPU Usage 5sec Rev ({#SNMPINDEX}) | <p>CISCO-PROCESS-MIB::cpmCPUTotal5secRev The overall CPU busy percentage in the last 5 second period. This object deprecates the object cpmCPUTotal5sec and increases the value range to (0..100). This object is deprecated by cpmCPUTotalMonIntervalValue.</p> | SNMP agent |
cpmCPUTotal5secRev[{#SNMPINDEX}]<p>Update: 30</p><p>LLD</p> | |||
$2 on Sensor “$1” | <p>CISCO-ENTITY-SENSOR-MIB::entSensorValue This variable reports the most recent measurement seen by the sensor.</p> | SNMP agent |
entSensorValue[”{#SNMPVALUE}”,Voltage]<p>Update: 60</p><p>LLD</p> | |||
Status of $2 Sensor “$1” | <p>CISCO-ENTITY-SENSOR-MIB::entSensorStatus This variable indicates the present operational status of the sensor.</p> | SNMP agent |
entSensorStatus[”{#SNMPVALUE}”,Voltage]<p>Update: 60</p><p>LLD</p> | |||
Manufacturer of $2 “$1” | <p>ENTITY-MIB::entPhysicalMfgName The name of the manufacturer of this physical component. The preferred value is the manufacturer name string actually printed on the component itself (if present).</p> | SNMP agent |
entPhysicalMfgName[”{#SNMPVALUE}”,”Fan Tray”]<p>Update: 86400</p><p>LLD</p> | |||
Model Name of $2 “$1” | <p>ENTITY-MIB::entPhysicalModelName The vendor-specific model name identifier string associated with this physical component. The preferred value is the customer-visible part number, which may be printed on the component itself.</p> | SNMP agent |
entPhysicalModelName[”{#SNMPVALUE}”,”Fan Tray”]<p>Update: 86400</p><p>LLD</p> | |||
Operational Status of $2 “$1” | <p>CISCO-ENTITY-FRU-CONTROL-MIB::cefcFanTrayOperStatus The operational state of the fan or fan tray.</p> | SNMP agent |
cefcFanTrayOperStatus[”{#SNMPVALUE}”,”Fan Tray”]<p>Update: 60</p><p>LLD</p> | |||
Serial Number of $2 “$1” | <p>ENTITY-MIB::entPhysicalSerialNum The vendor-specific serial number string for the physical entity. The preferred value is the serial number string actually printed on the component itself (if present).</p> | SNMP agent |
entPhysicalSerialNum[”{#SNMPVALUE}”,”Fan Tray”]<p>Update: 3600</p><p>LLD</p> | |||
SNMP traps for “{#SNMPVALUE}” sensor | <p>-</p> | SNMP trap |
snmptrap[“ciscoEnvMonTemperatureState.{#SNMPINDEX}[[:space:]](warning | critical | shutdown | normal)”]<p>Update: 0</p><p>LLD</p> |
Status of Temperature Sensor “$1” | <p>CISCO-ENVMON-MIB::ciscoEnvMonTemperatureState The current state of the testpoint being instrumented.</p> | SNMP agent |
ciscoEnvMonTemperatureState[”{#SNMPVALUE}”]<p>Update: 60</p><p>LLD</p> | |||
Temperature on Sensor “$1” | <p>CISCO-ENVMON-MIB::ciscoEnvMonTemperatureStatusValue The current measurement of the testpoint being instrumented.</p> | SNMP agent |
ciscoEnvMonTemperatureStatusValue[”{#SNMPVALUE}”]<p>Update: 60</p><p>LLD</p> | |||
Threshold Temperature on Sensor “$1” | <p>CISCO-ENVMON-MIB::ciscoEnvMonTemperatureThreshold The highest value that the associated instance of the object ciscoEnvMonTemperatureStatusValue may obtain before an emergency shutdown of the managed device is initiated.</p> | SNMP agent |
ciscoEnvMonTemperatureThreshold[”{#SNMPVALUE}”]<p>Update: 1800</p><p>LLD</p> | |||
OSPF “{#SNMPVALUE}” Neighbour State | <p>-</p> | SNMP trap |
snmptrap[“(ospfNbrStateChange).ospfNbrIpAddr[[:space:]]{#SNMPVALUE}[[:space:]].[[:space:]][a-zA-Z]+[[:space:]]$”]<p>Update: 0</p><p>LLD</p> | |||
Status of $2 Sensor “$1” | <p>CISCO-ENTITY-SENSOR-MIB::entSensorStatus This variable indicates the present operational status of the sensor.</p> | SNMP agent |
entSensorStatus[”{#SNMPVALUE}”,Power]<p>Update: 60</p><p>LLD</p> | |||
Value of $2 Sensor “$1” | <p>CISCO-ENTITY-SENSOR-MIB::entSensorValue This variable reports the most recent measurement seen by the sensor.</p> | SNMP agent |
entSensorValue[”{#SNMPVALUE}”,Power]<p>Update: 60</p><p>LLD</p> | |||
OSPF Interface “{SNMPVALUE}” State | <p>-</p> | SNMP trap |
snmptrap[“ospfIfStateChange.+ospfIfIpAddress[[:space:]]{#SNMPVALUE}[[:space:]].+ospfIfState[[:space:]][a-zA-Z]+”]<p>Update: 0</p><p>LLD</p> | |||
BGP Peer “{#SNMPINDEX}” State | <p>-</p> | SNMP trap |
snmptrap[“(bgpEstablished | bgpBackwardTransition | cbgpFsmStateChange).*bgpPeerState.{#SNMPINDEX}[[:space:]][a-zA-Z]+[[:space:]]”]<p>Update: 0</p><p>LLD</p> | |
BGP Peer “{#SNMPINDEX}” State | <p>-</p> | SNMP trap |
snmptrap[“(bgpBackwardTransition | cbgpFsmStateChange).*bgpPeerState.{#SNMPINDEX}[[:space:]][a-zA-Z]+[[:space:]]”]<p>Update: 0</p><p>LLD</p> | ||
Free memory on Memory Pool “$1” | <p>CISCO-MEMORY-POOL-MIB::ciscoMemoryPoolFree Indicates the number of bytes from the memory pool that are currently unused on the managed device.</p> | SNMP agent |
ciscoMemoryPoolFree[”{#SNMPVALUE}”]<p>Update: 60</p><p>LLD</p> | |||
Name of Memory Pool “$1” | <p>CISCO-MEMORY-POOL-MIB::ciscoMemoryPoolName A textual name assigned to the memory pool.</p> | SNMP agent |
ciscoMemoryPoolName[”{#SNMPVALUE}”]<p>Update: 3600</p><p>LLD</p> | |||
Total Memory Pool “$1” | <p>-</p> | Calculated |
ciscoMemoryPoolTotal[”{#SNMPVALUE}”]<p>Update: 3600</p><p>LLD</p> | |||
Used memory on Memory Pool “$1” | <p>CISCO-MEMORY-POOL-MIB::ciscoMemoryPoolUsed Indicates the number of bytes from the memory pool that are currently in use by applications on the managed device.</p> | SNMP agent |
ciscoMemoryPoolUsed[”{#SNMPVALUE}”]<p>Update: 300</p><p>LLD</p> | |||
Status of FAN “$1” | <p>CISCO-ENVMON-MIB::ciscoEnvMonFanState The current state of the fan being instrumented.</p> | SNMP agent |
ciscoEnvMonFanState[”{#SNMPVALUE}”]<p>Update: 60</p><p>LLD</p> | |||
Manufacturer of $2 “$1” | <p>ENTITY-MIB::entPhysicalMfgName The name of the manufacturer of this physical component. The preferred value is the manufacturer name string actually printed on the component itself (if present).</p> | SNMP agent |
entPhysicalMfgName[”{#SNMPVALUE}”,”Module”]<p>Update: 86400</p><p>LLD</p> | |||
Model Name of $2 “$1” | <p>ENTITY-MIB::entPhysicalModelName The vendor-specific model name identifier string associated with this physical component. The preferred value is the customer-visible part number, which may be printed on the component itself.</p> | SNMP agent |
entPhysicalModelName[”{#SNMPVALUE}”,”Module”]<p>Update: 86400</p><p>LLD</p> | |||
Operational Status of $2 “$1” | <p>ENTITY-STATE-MIB::entStateOper The operational state for this entity.</p> | SNMP agent |
entStateOper[”{#SNMPVALUE}”,”Module”]<p>Update: 60</p><p>LLD</p> | |||
Serial Number of $2 “$1” | <p>ENTITY-MIB::entPhysicalSerialNum The vendor-specific serial number string for the physical entity. The preferred value is the serial number string actually printed on the component itself (if present).</p> | SNMP agent |
entPhysicalSerialNum[”{#SNMPVALUE}”,”Module”]<p>Update: 3600</p><p>LLD</p> | |||
Status of Power Supply “$1” | <p>CISCO-ENVMON-MIB::ciscoEnvMonSupplyState The current state of the power supply being instrumented.</p> | SNMP agent |
ciscoEnvMonSupplyState[”{#SNMPVALUE}”]<p>Update: 60</p><p>LLD</p> | |||
$2 of Sensor “$1” | <p>CISCO-ENTITY-SENSOR-MIB::entSensorValue This variable reports the most recent measurement seen by the sensor.</p> | SNMP agent |
entSensorValue[”{#SNMPVALUE}”,Amperage]<p>Update: 60</p><p>LLD</p> | |||
Status of $2 Sensor “$1” | <p>CISCO-ENTITY-SENSOR-MIB::entSensorStatus This variable indicates the present operational status of the sensor.</p> | SNMP agent |
entSensorStatus[”{#SNMPVALUE}”,Amperage]<p>Update: 60</p><p>LLD</p> |
Name | Description | Expression | Priority | ||
---|---|---|---|---|---|
BGP Peer “{#SNMPINDEX}”->”{#SNMPVALUE}” State changed | <p>-</p> | <p>Expression: nodata(/Cisco_6500/snmptrap[“(bgpEstablished | bgpBackwardTransition | cbgpFsmStateChange).*bgpPeerState .{#SNMPINDEX}[[:space:]][a-zA-Z]+[[:space:]]”],10m)=0</p><p>Recovery expression: </p> | average |
BGP Peer “{#SNMPINDEX}”->”{#SNMPVALUE}” State changed | <p>-</p> | <p>Expression: nodata(/Cisco_6500/snmptrap[“(bgpBackwardTransition | cbgpFsmStateChange).*bgpPeerState .{#SNMPINDEX}[[:space:]][a-zA-Z]+[[:space:]]”],10m)=0</p><p>Recovery expression: </p> | average | |
OSPF Interface “{#SNMPVALUE}” State has been changed | <p>-</p> | <p>Expression: nodata(/Cisco_6500/snmptrap[“ospfIfStateChange.+ospfIfIpAddress[[:space:]]{#SNMPVALUE}[[:space:]].+ospfIfState[[:space:]][a-zA-Z]+”],10m)=0</p><p>Recovery expression: </p> | average | ||
OSPF Neighbor {#SNMPVALUE} has been changed | <p>-</p> | <p>Expression: nodata(/Cisco_6500/snmptrap[“(ospfNbrStateChange).ospfNbrIpAddr[[:space:]]{#SNMPVALUE}[[:space:]].[[:space:]][a-zA-Z]+[[:space:]]$”],10m)=0</p><p>Recovery expression: </p> | average | ||
Power Sensor “{#SNMPVALUE}” is nonoperational | <p>-</p> | <p>Expression: last(/Cisco_6500/entSensorStatus[”{#SNMPVALUE}”,Power])=3</p><p>Recovery expression: </p> | high | ||
Power Sensor “{#SNMPVALUE}” is unavailable | <p>-</p> | <p>Expression: last(/Cisco_6500/entSensorStatus[”{#SNMPVALUE}”,Power])=2</p><p>Recovery expression: </p> | average | ||
Amperage Sensor “{#SNMPVALUE}” is nonoperational | <p>-</p> | <p>Expression: last(/Cisco_6500/entSensorStatus[”{#SNMPVALUE}”,Amperage])=3</p><p>Recovery expression: </p> | high | ||
Amperage Sensor “{#SNMPVALUE}” is unavailable | <p>-</p> | <p>Expression: last(/Cisco_6500/entSensorStatus[”{#SNMPVALUE}”,Amperage])=2</p><p>Recovery expression: </p> | average | ||
Module “{#SNMPVALUE}” is inoperable | <p>-</p> | <p>Expression: last(/Cisco_6500/entStateOper[”{#SNMPVALUE}”,”Module”])=2</p><p>Recovery expression: </p> | disaster | ||
Voltage Sensor “{#SNMPVALUE}” is nonoperational | <p>-</p> | <p>Expression: last(/Cisco_6500/entSensorStatus[”{#SNMPVALUE}”,Voltage])=3</p><p>Recovery expression: </p> | high | ||
Voltage Sensor “{#SNMPVALUE}” is unavailable | <p>-</p> | <p>Expression: last(/Cisco_6500/entSensorStatus[”{#SNMPVALUE}”,Voltage])=2</p><p>Recovery expression: </p> | average | ||
Status of Fan Tray “{#SNMPVALUE}” is in partial failure | <p>-</p> | <p>Expression: last(/Cisco_6500/cefcFanTrayOperStatus[”{#SNMPVALUE}”,”Fan Tray”])=4</p><p>Recovery expression: </p> | warning | ||
Status of Fan Tray “{#SNMPVALUE}” is powered down | <p>-</p> | <p>Expression: last(/Cisco_6500/cefcFanTrayOperStatus[”{#SNMPVALUE}”,”Fan Tray”])=3</p><p>Recovery expression: </p> | high | ||
High CPU #{#SNMPINDEX} Usage | <p>-</p> | <p>Expression: last(/Cisco_6500/cpmCPUTotal5minRev[{#SNMPINDEX}])>95</p><p>Recovery expression: </p> | high | ||
Status of FAN “{#SNMPVALUE}” is critical | <p>-</p> | <p>Expression: last(/Cisco_6500/ciscoEnvMonFanState[”{#SNMPVALUE}”])=3</p><p>Recovery expression: </p> | average | ||
Status of FAN “{#SNMPVALUE}” is non-operable | <p>-</p> | <p>Expression: last(/Cisco_6500/ciscoEnvMonFanState[”{#SNMPVALUE}”])=2</p><p>Recovery expression: </p> | warning | ||
Status of FAN “{#SNMPVALUE}” is not functioning | <p>-</p> | <p>Expression: last(/Cisco_6500/ciscoEnvMonFanState[”{#SNMPVALUE}”])=6</p><p>Recovery expression: </p> | average | ||
Status of FAN “{#SNMPVALUE}” is shutdown | <p>-</p> | <p>Expression: last(/Cisco_6500/ciscoEnvMonFanState[”{#SNMPVALUE}”])=4</p><p>Recovery expression: </p> | high | ||
High utilization of Memory Pool “{#SNMPVALUE}” | <p>-</p> | <p>Expression: last(/Cisco_6500/ciscoMemoryPoolUsed[”{#SNMPVALUE}”])>last(/Cisco_6500/ciscoMemoryPoolTotal[”{#SNMPVALUE}”])*0.9</p><p>Recovery expression: </p> | average | ||
Status of Power Supply “{#SNMPVALUE}” is critical | <p>-</p> | <p>Expression: last(/Cisco_6500/ciscoEnvMonSupplyState[”{#SNMPVALUE}”])=3</p><p>Recovery expression: </p> | average | ||
Status of Power Supply “{#SNMPVALUE}” is non-operable | <p>-</p> | <p>Expression: last(/Cisco_6500/ciscoEnvMonSupplyState[”{#SNMPVALUE}”])=2</p><p>Recovery expression: </p> | warning | ||
Status of Power Supply “{#SNMPVALUE}” is not functioning | <p>-</p> | <p>Expression: last(/Cisco_6500/ciscoEnvMonSupplyState[”{#SNMPVALUE}”])=6</p><p>Recovery expression: </p> | average | ||
Status of Power Supply “{#SNMPVALUE}” is shutdown | <p>-</p> | <p>Expression: last(/Cisco_6500/ciscoEnvMonSupplyState[”{#SNMPVALUE}”])=4</p><p>Recovery expression: </p> | high | ||
Temperature Sensor “{#SNMPVALUE}” is abnormal | <p>-</p> | <p>Expression: last(/Cisco_6500/ciscoEnvMonTemperatureState[”{#SNMPVALUE}”])=2</p><p>Recovery expression: </p> | warning | ||
Temperature Sensor “{#SNMPVALUE}” is abnormal | <p>-</p> | <p>Expression: last(/Cisco_6500/ciscoEnvMonTemperatureState[”{#SNMPVALUE}”])=3</p><p>Recovery expression: </p> | high | ||
Temperature Sensor “{#SNMPVALUE}” is not functioning | <p>-</p> | <p>Expression: last(/Cisco_6500/ciscoEnvMonTemperatureState[”{#SNMPVALUE}”])=6</p><p>Recovery expression: </p> | information | ||
Temperature Sensor “{#SNMPVALUE}” is shutdown | <p>-</p> | <p>Expression: last(/Cisco_6500/ciscoEnvMonTemperatureState[”{#SNMPVALUE}”])=4</p><p>Recovery expression: </p> | disaster | ||
High CPU #{#SNMPINDEX} Usage (LLD) | <p>-</p> | <p>Expression: last(/Cisco_6500/cpmCPUTotal5minRev[{#SNMPINDEX}])>95</p><p>Recovery expression: </p> | high | ||
Voltage Sensor “{#SNMPVALUE}” is nonoperational (LLD) | <p>-</p> | <p>Expression: last(/Cisco_6500/entSensorStatus[”{#SNMPVALUE}”,Voltage])=3</p><p>Recovery expression: </p> | high | ||
Voltage Sensor “{#SNMPVALUE}” is unavailable (LLD) | <p>-</p> | <p>Expression: last(/Cisco_6500/entSensorStatus[”{#SNMPVALUE}”,Voltage])=2</p><p>Recovery expression: </p> | average | ||
Status of Fan Tray “{#SNMPVALUE}” is in partial failure (LLD) | <p>-</p> | <p>Expression: last(/Cisco_6500/cefcFanTrayOperStatus[”{#SNMPVALUE}”,”Fan Tray”])=4</p><p>Recovery expression: </p> | warning | ||
Status of Fan Tray “{#SNMPVALUE}” is powered down (LLD) | <p>-</p> | <p>Expression: last(/Cisco_6500/cefcFanTrayOperStatus[”{#SNMPVALUE}”,”Fan Tray”])=3</p><p>Recovery expression: </p> | high | ||
Temperature Sensor “{#SNMPVALUE}” is abnormal (LLD) | <p>-</p> | <p>Expression: last(/Cisco_6500/ciscoEnvMonTemperatureState[”{#SNMPVALUE}”])=2</p><p>Recovery expression: </p> | warning | ||
Temperature Sensor “{#SNMPVALUE}” is abnormal (LLD) | <p>-</p> | <p>Expression: last(/Cisco_6500/ciscoEnvMonTemperatureState[”{#SNMPVALUE}”])=3</p><p>Recovery expression: </p> | high | ||
Temperature Sensor “{#SNMPVALUE}” is not functioning (LLD) | <p>-</p> | <p>Expression: last(/Cisco_6500/ciscoEnvMonTemperatureState[”{#SNMPVALUE}”])=6</p><p>Recovery expression: </p> | information | ||
Temperature Sensor “{#SNMPVALUE}” is shutdown (LLD) | <p>-</p> | <p>Expression: last(/Cisco_6500/ciscoEnvMonTemperatureState[”{#SNMPVALUE}”])=4</p><p>Recovery expression: </p> | disaster | ||
OSPF Neighbor {#SNMPVALUE} has been changed (LLD) | <p>-</p> | <p>Expression: nodata(/Cisco_6500/snmptrap[“(ospfNbrStateChange).ospfNbrIpAddr[[:space:]]{#SNMPVALUE}[[:space:]].[[:space:]][a-zA-Z]+[[:space:]]$”],10m)=0</p><p>Recovery expression: </p> | average | ||
Power Sensor “{#SNMPVALUE}” is nonoperational (LLD) | <p>-</p> | <p>Expression: last(/Cisco_6500/entSensorStatus[”{#SNMPVALUE}”,Power])=3</p><p>Recovery expression: </p> | high | ||
Power Sensor “{#SNMPVALUE}” is unavailable (LLD) | <p>-</p> | <p>Expression: last(/Cisco_6500/entSensorStatus[”{#SNMPVALUE}”,Power])=2</p><p>Recovery expression: </p> | average | ||
OSPF Interface “{#SNMPVALUE}” State has been changed (LLD) | <p>-</p> | <p>Expression: nodata(/Cisco_6500/snmptrap[“ospfIfStateChange.+ospfIfIpAddress[[:space:]]{#SNMPVALUE}[[:space:]].+ospfIfState[[:space:]][a-zA-Z]+”],10m)=0</p><p>Recovery expression: </p> | average | ||
BGP Peer “{#SNMPINDEX}”->”{#SNMPVALUE}” State changed (LLD) | <p>-</p> | <p>Expression: nodata(/Cisco_6500/snmptrap[“(bgpEstablished | bgpBackwardTransition | cbgpFsmStateChange).*bgpPeerState .{#SNMPINDEX}[[:space:]][a-zA-Z]+[[:space:]]”],10m)=0</p><p>Recovery expression: </p> | average |
BGP Peer “{#SNMPINDEX}”->”{#SNMPVALUE}” State changed (LLD) | <p>-</p> | <p>Expression: nodata(/Cisco_6500/snmptrap[“(bgpBackwardTransition | cbgpFsmStateChange).*bgpPeerState .{#SNMPINDEX}[[:space:]][a-zA-Z]+[[:space:]]”],10m)=0</p><p>Recovery expression: </p> | average | |
High utilization of Memory Pool “{#SNMPVALUE}” (LLD) | <p>-</p> | <p>Expression: last(/Cisco_6500/ciscoMemoryPoolUsed[”{#SNMPVALUE}”])>last(/Cisco_6500/ciscoMemoryPoolTotal[”{#SNMPVALUE}”])*0.9</p><p>Recovery expression: </p> | average | ||
Status of FAN “{#SNMPVALUE}” is critical (LLD) | <p>-</p> | <p>Expression: last(/Cisco_6500/ciscoEnvMonFanState[”{#SNMPVALUE}”])=3</p><p>Recovery expression: </p> | average | ||
Status of FAN “{#SNMPVALUE}” is non-operable (LLD) | <p>-</p> | <p>Expression: last(/Cisco_6500/ciscoEnvMonFanState[”{#SNMPVALUE}”])=2</p><p>Recovery expression: </p> | warning | ||
Status of FAN “{#SNMPVALUE}” is not functioning (LLD) | <p>-</p> | <p>Expression: last(/Cisco_6500/ciscoEnvMonFanState[”{#SNMPVALUE}”])=6</p><p>Recovery expression: </p> | average | ||
Status of FAN “{#SNMPVALUE}” is shutdown (LLD) | <p>-</p> | <p>Expression: last(/Cisco_6500/ciscoEnvMonFanState[”{#SNMPVALUE}”])=4</p><p>Recovery expression: </p> | high | ||
Module “{#SNMPVALUE}” is inoperable (LLD) | <p>-</p> | <p>Expression: last(/Cisco_6500/entStateOper[”{#SNMPVALUE}”,”Module”])=2</p><p>Recovery expression: </p> | disaster | ||
Status of Power Supply “{#SNMPVALUE}” is critical (LLD) | <p>-</p> | <p>Expression: last(/Cisco_6500/ciscoEnvMonSupplyState[”{#SNMPVALUE}”])=3</p><p>Recovery expression: </p> | average | ||
Status of Power Supply “{#SNMPVALUE}” is non-operable (LLD) | <p>-</p> | <p>Expression: last(/Cisco_6500/ciscoEnvMonSupplyState[”{#SNMPVALUE}”])=2</p><p>Recovery expression: </p> | warning | ||
Status of Power Supply “{#SNMPVALUE}” is not functioning (LLD) | <p>-</p> | <p>Expression: last(/Cisco_6500/ciscoEnvMonSupplyState[”{#SNMPVALUE}”])=6</p><p>Recovery expression: </p> | average | ||
Status of Power Supply “{#SNMPVALUE}” is shutdown (LLD) | <p>-</p> | <p>Expression: last(/Cisco_6500/ciscoEnvMonSupplyState[”{#SNMPVALUE}”])=4</p><p>Recovery expression: </p> | high | ||
Amperage Sensor “{#SNMPVALUE}” is nonoperational (LLD) | <p>-</p> | <p>Expression: last(/Cisco_6500/entSensorStatus[”{#SNMPVALUE}”,Amperage])=3</p><p>Recovery expression: </p> | high | ||
Amperage Sensor “{#SNMPVALUE}” is unavailable (LLD) | <p>-</p> | <p>Expression: last(/Cisco_6500/entSensorStatus[”{#SNMPVALUE}”,Amperage])=2</p><p>Recovery expression: </p> | average |
There are no macros links in this template.
There are no template links in this template.
There are no discovery rules in this template.
Name | Description | Type | Key and additional info | |
---|---|---|---|---|
Type of remote session | <p>-</p> | SNMP trap |
snmptrap[“tslineSesType”]<p>Update: 0</p> | |
LSA has been originated | <p>OSPF-TRAP-MIB::ospfOriginateLsa</p> | SNMP trap |
snmptrap[“ospfOriginateLsa”]<p>Update: 0</p> | |
Attack Filter changes | <p>The system generates this notification to indicate that the cscaFilterStatus of the attack filter for cscaType has changed due to the reason determined by cscaDescription. The system limits the generation of this notifications for the same cscaType to a five-second interval.</p> | SNMP trap |
snmptrap[“cscaFilterChange”]<p>Update: 0</p> | |
Status of Attack Filter | <p>-</p> | SNMP trap |
snmptrap[“cscaFilterStatus”]<p>Update: 0</p> | |
SSH Sessions | <p>CISCO-SECURE-SHELL-MIB::cssSessionHostAddr</p> | SNMP trap |
snmptrap[“cssSessionHostAddr”]<p>Update: 0</p> | |
Source of Command | <p>-</p> | SNMP trap |
snmptrap[“ccmHistoryEventCommandSource”]<p>Update: 0</p> | |
OSPF Interface State | <p>OSPF-MIB::ospfIfState The OSPF Interface State.</p> | SNMP trap |
snmptrap[“ospfIfState”]<p>Update: 0</p> | |
BGP Peer State | <p>BGP4-MIB::bgpPeerState CISCO-BGP4-MIB::cbgpPeer2State The BGP peer connection state.</p> | SNMP trap |
snmptrap[“bgpPeerState | cbgpPeer2State”]<p>Update: 0</p> |
MPLS L3 State | <p>MPLS-L3VPN-STD-MIB::mplsL3VpnVrfUp MPLS-L3VPN-STD-MIB::mplsL3VpnVrfDown</p> | SNMP trap |
snmptrap[“mplsL3VpnVrf[Up | Down]”]<p>Update: 0</p> |
LSA aged to MaxAge | <p>-</p> | SNMP trap |
snmptrap[“ospfMaxAgeLsa”]<p>Update: 0</p> | |
OSP TX Retransmits | <p>-</p> | SNMP trap |
snmptrap[“ospfTxRetransmit”]<p>Update: 0</p> | |
OSPF neighbour state | <p>1 : down 2 : attempt 3 : init 4 : twoWay 5 : exchangeStart 6 : exchange 7 : loading 8 : full</p> | SNMP trap |
snmptrap[“ospfNbrStateChange.*ospfNbrState[[:space:]]”]<p>Update: 0</p> | |
BFD Sessions | <p>CISCO-IETF-BFD-MIB::ciscoBfdSessDown and ciscoBfdSessUp</p> | SNMP trap |
snmptrap[“ciscoBfdSess(Up | Down)”]<p>Update: 0</p> |
There are no triggers in this template.